sieve analysis what's the meaning or gonna happen if the So is zero

Q: An open rectangular Bốx is to bê made from a 9 x 12 inch piece of tin by cutting a square of side x…

A:

Q: What the deviator stress?

A: The deviator stress can be defined as it is the difference between the principal major and minor…

Q: Four 28 bars are to be placed on a single layer in a beam having a width of 350 mm with shear…

A: To find out the actual spacing of mains bar which has diameter 28 mm.

Q: What is a pitot tube and what is its use?

A: Pitot tube is a device used to measure the velocity of fluid in fluid dynamics. It is a small device…

Q: Where does “stress at a point” analysis can be applicable?

A: The analysis of stress at a point is applicable to find the mechanical properties of the solid…

Q: Explain the reason why the calculated theoretical strength (o theo) is much higher than the measured…

A: Theoretical strength for solid is given by; σtheo≃E10 Where, E- Young's modulus σtheo- maximum…

Q: What do you mean by bulk density of the particulate layer?

A: Bulk density is defined as the ratio of the mass of the particles to the total volume of the…

Q: what conclusions you can draw from this graph

A: Consider the given graph. From the graph, it can be seen that as the hardness of the steel…

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

A:

Q: Write in detail foremost engineering problems in cement industry

A: Main problems in Cement Industry (In pyro-processing) cyclone jamming Kiln inlet jamming large…

Q: Glass's production flow chart should be sketched out. What are the advantages and disadvantages of…

A: Introductions: This question deals with the advantages and disadvantages of using glass in…

Q: in your own words give 3 concrete example where you can apply the kinematics of particles as a civil…

A: Kinematics is the study of the motion of points, objects, and groups of objects without considering…

Q: How to prepare samples and perform thermal expansion tests ASTM E831? b) how to perform tensile…

A: Testing materials are an important component of understanding their physical properties, helping in…

Q: How many cubic yards of aggregate must be ordered for a road base 16 inches thick and 2 miles long…

A: The thickness of the road base = 16 inLength of the road = 2 milesThe top width of the road = 30…

Q: A steel plate is 300 mm wide and 10 mm thick. A rivet of nominal diameter of 16 mm is driven into…

A: Diameter of the hole =do+1.5    (do≤25mm)d=16+1.5=17.5mm

Q: Relating to geotextiles (geofabrics), what is a significant difference in appearance and texture…

A: Geotextiles are defined as the textile structures which are permeable and made from polypropylene or…

Q: .  Explain the three stages in casting process and its applications.

A: Stages of casting: While each casting method creates unique challenges and process enhancements, all…

Q: Compare between Rockwell and brinell hardness test?

A: Let us analyse the question in step 2.

Q: Why is it important to control how much shrink a film is capable of?

A: Shrink wrapping (also called wrinkling film or shrink wrapping) is a flexible polymer material used…

Q: A device that creates motion of the sieves to cause the particles to bounce, tumble, or otherwise…

A: Given data in question  Sieves Motion of sieves To find out  Device which creates sieve motion

Q: in the table based on the information that has been given Us Standard Sieve No. Sieve Opening (mm)…

A:

Q: 3. Design the flexural steel for a 5-inch thick simply-supported interior reinforced concrete…

A:

Q: Could you please help determine elastic center C Where the square has a  modulus of elasticity =…

A: Determine elastic center CWhere the square has a  modulus of elasticity = E_w and  the two riangle…

Q: What is your realization about smart fabrics?

A: Solution:- Smart textiles applications are able to sense and respond to changes in their…

Q: Explain the specifications of tamping rod used in cube filling for cube test ?

A: Tamping rods are used for strengthening of concrete which is mixed freshly in tests for slump, air…

Q: ensile strength of 67.819 psi. The original gage length was 2 inches

A: Given:- tensile strength=67.819psi originalgauge length =2 inches gauge length2.75 inches To find:-…

Q: What is the modulus of fineness? how it is calculated, and how important it is.

A: Modulus of fineness- It is defined as an empirical formula that is obtained by dividing the total…

Q: What are Superalloys? What are its properties? Where are they most used

A: Superalloys are complex, high-performance alloys, which have a high tolerance of oxidising…

Q: 8. How can we write specific weight using the FLT system? a) [F] b) [F][T] c) [F][L][T] d) [L]

A: You can wright specific weight in FLT system as. Formula of specific weight =N/m^3 Specific weight…

Q: Explain how to measure cement

A: Cement: Cement is a material which has adhesive and cohesive properties only in tghe presence of…

Q: Define the importance of material testing in the design process in one word, and explain why you…

A: Material testing: Materials testing is a respected and established technique that is used to…

Q: Provide an explanation of the concept of testing isolated parts.

A: The concept of testing the isolated parts refers to the practice of testing individual components or…

Q: Where does the value for yc in step two come from?

A: Since the unit weight of the concrete for the beam is not given in the problem. Usually the unit…

Q: Discuss the advantages and disadvantages of different methods in determining particle size?

A: Air Permeability Fisher Method:-  A fisher sub seive sizer works on the air permeability fisher…

Q: What factors can affect the porosity due to the passage of the fluid?

A: The flow of fluid in the soil is explained by Darcy's law. Darcy's law is expressed as, Q = kiA…

Q: give 3 concrete examples where you can apply kinematics of particles as a civil enginee

A: Kinematics is the study of the motion of points, objects, and groups of objects without considering…

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.