K/s bläi 3 :Q1 Find the capillary rise ( h) in the tube shown in the figure for a water-air-glass interface with O= 20 if the tube diameter (D) is 3 mm and the temperature is 20 c. Take surface tension (a) = 0.2 N/m. 19.641 mm O 16.327 mm 10.986 mm 12.014 mm 9.325 mm 17.975 mm 23.159 mm 25.544 mm 14.218 mm 21.014 mm

K/s bläi 3 :Q1 Find the capillary rise ( h) in the tube shown in the figure for a water-air-glass interface with O= 20 if the tube diameter (D) is 3 mm and the temperature is 20 c. Take surface tension (a) = 0.2 N/m. 19.641 mm O 16.327 mm 10.986 mm 12.014 mm 9.325 mm 17.975 mm 23.159 mm 25.544 mm 14.218 mm 21.014 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the figure shown below, the surface tension for a water-glass interface is 0.078N/m, d=15mm 7. Calculate the capillary rise in the tube in mm. d a. 6.3455 mm b. 4.7299 mm c. 2.1203 mm d. 5.3154 mm 8. Determine the total force due tO surface tension in N. h a. 2.90x10-4 N b. 3.68x10-3N c. 1.85x10 4N d. 4.18x103 N
The cross section of a slit rectangular tube ofconstant thickness is shown in the figures.(a) Derive the following formula for the distance efrom the centerline of the wall of the tube in thefigure part a to the shear center S: e = [b(2h+3b)/[2(h+3b)] (b) Find an expression for e if flanges with the samethickness as that of the tube are added as shownin figure part b.
Need answer now
ASAP
Both wires have a cross sectional area of 17 mm2 and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible.
Q.6) If the tension in the chain AB is 150 N, determine the component of the chain tension vector parallel and perpendicular to the door. O1900 mm 900 mm D 1200 mm A 30°
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A.
The pipe assembly is subjected to a force of 600 N at B. 150 mm 150 mm Part A 400 mm B 60° 30° 600 N 500 mm Tap image to zoom Determine the magnitude of the resultant internal normal force acting on the cross section at C. Express your answer to three significant
е Q2). A 20m steel tape supported at both ends was used to measure horizontal P distance of CD at a temperature of 35 °C and 60 N tension force measured distance was 350m. Under the standard conditions was found that the tape 19.95m length. Find the actual horizontal distance between CD if: Ts Standard temperature 25 °C Coefficient of thermal expansion of steel tape = 11.6x10-6/°C Po Standard tension = 100N. Modulus of elasticity (E) = 210 kN/mm² Cross-sectional area of the tape = 2 mm² The weight of this tape between supports 8 N
Problem 6: Replace the force of F = 80 N acting on the pipe assembly by an equivalent resultant force and couple moment at point A. A 400 mm 300 mm 200 mm 200 mm 250 mm 40° 30° F = 80 N N
View Policies Current Attempt in Progress Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against the smooth slot in the triangular plate. E 370 N 110 mm 140 mm 115 mm 135 mm Answer: D = i N
The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw - 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.