A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A

A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. A T 200 mm 200 mm B -300 mm- 200 mm D 300 mm E
135 mm 85 mm σ, = -58 MPa E = 105 GPa D = 0.33 Beer & Johnston & DeWolf & Mazurek 2.86 (a) For the axial loading shown, determine the change in height and the change in volume of the brass cylinder shown. (b) Solve part a, assuming that the loading is hydrostatic with Ox= Oy = O₂ = -70 MPa
Solve for M/I
4 m 450 mm [s0 mn [50 mn 18 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water, helshe stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B8-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 mis?. Provide all steps of your working and solutions handwriten; include diagrams and coordinate systems. a. Determine the reactions at each support A and B. Use the variable w for the weight of the diver, include a free-body diagram.
Q2/A rigid bar the weight-80 kN is supported as shown in the Fig, compute the temperature change that will cause the stress in the steel rod to be 55 MPa. Assume the coefficients of linear expansion are 11.7 μm/(m °C) for steel and 18.9 μm/ (m-°C) for bronze. Bronze LAUM 1300 mm Steel E 83 GPa 1.5 m 320 mm² 300 GPS
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.500 in. and a wall thickness of 0.500 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.000-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). The bar is loaded as shown. Assume L1= 55 in., L2= 40 in., L3 = 25 in., R = 31 kips, Q = 11 kips, and P = 27 kips. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial assembly. R A B R L1 L2 L3 Answers: (a) 81 i in. in. An (9) (c) Omax i ksi
show breif solution
It is required to deisgn a close coiled helical spring which shall deflect10 mm under an axial load of 100 N at a shear stresss of 90 N/mm². Modulus of rigidity is 8 x 104 MPa. The mean diameter of the coils is 10 times diameter of the wire. Find the diameter and length of the wire necessary to form the spring.
A flat steel bar, 30 mm wide by 2 mm thick and 1.6 m long, is bent by couples applied at the ends so that the midpoint deflection is 23 mm. Compute the maximum stress in the bar. Use E =210GPA. Answer must be in MPa.
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
An aluminum bar of cross-section 450 ??² is acted upon by the forces as shown in the figure. Determine the total elongation of the bar. Use ? = 70 ???.