Question [1] In the figure below, the mass of the bucket is 5 kg. It is kept in equilibrium by the wires which are connected at rings B and E. You are required to: a) b) Draw the Free-Body Diagram. Determine the tension developed in wire AB. Determine the tension developed in wires EB and ED. B 130⁰ E 30° D

Question [1] In the figure below, the mass of the bucket is 5 kg. It is kept in equilibrium by the wires which are connected at rings B and E. You are required to: a) b) Draw the Free-Body Diagram. Determine the tension developed in wire AB. Determine the tension developed in wires EB and ED. B 130⁰ E 30° D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The forces shown are applied to the pins at B and C, respectively. Calculate the magnitude of the pin reaction at F. Neglect the weights of the members. *Write your answer in two decimal places. 70KN C. 5m 30KN E 2 m 2.5 m 1.5m F భంగ 6m ద ఉ
Use 4 decimal places during computation and 2 decimal places for the final answer. Please write you’re your solution on a paper and draw the FBD.
Problem 8.61 Part A The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact is μ= 0.29. (Figure 1) Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. Figure k = 20 lb/in. A 60° 45° B 1 of 1 P= Value Submit Request Answer Provide Feedback ? Units
Let P = 319 lb, a = 38 ft, b = 12 ft, and G = 11 deg. Type the unit, lb, after typing your numerical answer. 1b. Determine the magnitude of the x component of the reaction at support A. The weight of the rod is negligible. P b m X
Already answered in Bartleby. Do not copy the solutions. Please double check the solutions! Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) 1. The line of action of the 3000 lb force runs through te points A and B as shown in the figure. Determine: x scalar component of F
load A =350 N load b=400 N
Need only a handwritten solution only (not a typed one).
The circular shaft AB consists of a 18 mm diameter solid steel cylinder in which a 8 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 50 Nm. Determine the ratio of lengths L₁/L₂. Input your answer to two decimal places. 4₁ L₂ A 150 Nm B
The 9-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m 0 B HA 2 m 50 N·m 1 of 1 Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. A= [5] ΑΣΦ ↓1 vec 1 Submit Provide Feedback Request Answer ?
3. The small sphere shown below has held by two wires with tension To. sphere is released from equilibrium. Determine the ratio To/T1, where T1 is the tension in the remaining wire immediately after the other mass of 2kg. It is initially One wire is cut and the small a one is cut. 30 30
Solve for the reaction forces of the given figure from point a to b. pls show your complete solutions. thank you
Please correct my understanding of this question. -In the equation of the moment at point A, there is a value, 36(11.5). I assume that is a force from the distributed load. -If you are finding the moment at point A, wouldn't you only need one value from the distributed load which is 27(10)? So my question is how do you get the value of 36 and 11.5, separately. And what is it for?