20. A thrust of 30 kN along the axis of a shaft is taken by a pivot bearingconsisting of the frustum of a cone.The outer and inner diameters are 200 mmand 100 mm and the semi-angle of the cone is 60°. The shaft speed is 200 rev/min0-02. Assuming that the intensity of pressure is uniform over thesurface of the bearing, find, from first principles (a) the magnitude of this pros-sure, in N/m²; (b) the power absorbed in friction. (U. Lond.)and(Ans.: 1.272 MN/m²; 1.13 kW)

Answered: Image /qna-images/answer/e200405e-b99d-422f-80ce-eb5af08743c5.jpg

KIN along the axis of a shaft is takon consisting of the frustum of a cone. The outer and inner diameters are 200 mm and 100 mm and the semi-angle of the cone is 60°. The shaft speed is 200 rev/min and μ = 0-02. Assuming that the intensity of pressure is uniform over the surface of the bearing, find, from first principles (a) the magnitude of this pres- sure, in N/m²; (b) the power absorbed in friction. (U. Lond.) (Ans.: 1.272 MN/m2; 1.13 kW)

KIN along the axis of a shaft is takon consisting of the frustum of a cone. The outer and inner diameters are 200 mm and 100 mm and the semi-angle of the cone is 60°. The shaft speed is 200 rev/min and μ = 0-02. Assuming that the intensity of pressure is uniform over the surface of the bearing, find, from first principles (a) the magnitude of this pres- sure, in N/m²; (b) the power absorbed in friction. (U. Lond.) (Ans.: 1.272 MN/m2; 1.13 kW)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Examples & The Inlet to pump is 10.50m above the bottom of sump from which it draw water through a suction pipe. If the pressure at the pamp inlet is not to fall bellow 28 kN/m² absolute, work out the minimum depth of water in the tank 6.019 m O 15m 0 3.019 m O 9.019 m O 1.019 m O
A very tall 10-cm-diameter vase contains water at a depth of 6 cm. When spun steadily to achieve rigid-body rotation, the bottom is just started to get exposed. What is the rotation rate, in RPM, for this condition?
Find hught P⋅E= 33.555 m = 3kg g=10m/s2
I need the answer as soon as possible
For the following mechanical systems, get the equations of motion in Domain of Laplace
1 and 2 are rolling cylinders connecting shafts A and B. 3 and 4 are cylinders fastened to these same shafts and slipping on each other at P. Find the diameters of 3 and 4 if the surface speed of 4 is twice that of 3.
Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW and the brake specific fuel consumption (bsfc) is 290 g/kW.hr. Air consumption is measured by means of air-box method with orifice diameter 3.2-cm and discharge coefficient 0.62 and the pressure difference across the orifice is 150-mm-water. The ambient pressure and the temperature in the test room is 101 kPa and 20 °C. Assume: CV = 43.9 MJ/kg, PH20 =10³ kg/m³, comb = 98%, mech = 87%. (i) Determine the bmep, AFR, №v, power loss as friction, th,b. (ii) draw up the heat balance sheet on percentage basis, if the cooling water flow is 15 kg/min; rise in temperature of cooling water is 33 °C; exhaust gas temperature is 485 °C; Cpw is 4.2 kJ/kg.K and Cpexh is 1.25 kJ/kg.K.
I need the answer quickly
Please show your step by step solution thank you
I need the answer as soon as possible
Q2: Calculate the force components Fx, Fy needed to hold the stationary vane or fig. (2). Take V15m/s, p=1000 kg/m and D=50 mm. V=15 m/s 45° + Fx Fig.2 30 D=50 mm V=15 m/s
Problem (2) Neglecting friction, find the horizontal force of the water (N) on the horizontal bend shown in the figure. V, = 10 m/s %3D 8 cm dia. V2 4 cm Answer: