KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when Po was 0.04 and and an acceptance number of 1. Answer the following questions. consumer's risk of 0.20 when p, was 0.25. Consider the acceptance sampling plan based on a sample size of 1! (a) What is the producer's risk for the n = 15, c = 1 sampling plan? (Round your answer to four decimal places.) (b) What is the consumer's risk for the n = 15, c = 1 sampling plan? (Round your answer to four decimal places.) (c) Does then = 15, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. O The producer's risk is not acceptable since it is greater than 0.10.

Practical Management Science
6th Edition
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:WINSTON, Wayne L.
Chapter2: Introduction To Spreadsheet Modeling
Section: Chapter Questions
Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...
icon
Related questions
icon
Concept explainers
Topic Video
Question
KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are
purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it
overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to
ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be
subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives.
Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of
overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are
found in the sample, the lot is probably of poor quality and should be rejected.
The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p, was 0.25. Consider the acceptance sampling plan based on a sample size of 15
and an acceptance number of 1. Answer the following questions.
(a) What is the producer's risk for the n = 15, c = 1 sampling plan? (Round your answer to four decimal places.)
(b) What is the consumer's risk for the n =
15, c = 1 sampling plan? (Round your answer to four decimal places.)
(c) Does the n =
15, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.)
The producer's risk is acceptable since it is less than 0.10.
The producer's risk is not acceptable since it is greater than 0.10.
The consumer's risk is acceptable since it is less than 0.20.
The consumer's risk is not acceptable since it is greater than 0.20.
O O O O
Transcribed Image Text:KALI, Inc., manufactures home appliances that are marketed under a variety of trade names. However, KALI does not manufacture every component used in its products. Several components are purchased directly from suppliers. For example, one of the components that KALI purchases for use in home air conditioners is an overload protector, a device that turns off the compressor if it overheats. The compressor can be seriously damaged if the overload protector does not function properly, and therefore KALI is concerned about the quality of the overload protectors. One way to ensure quality would be to test every component received through an approach known as 100% inspection. However, to determine proper functioning of an overload protector, the device must be subjected to time-consuming and expensive tests, and KALI cannot justify testing every overload protector it receives. Instead, KALI uses an acceptance sampling plan to monitor the quality of the overload protectors. The acceptance sampling plan requires that KALI's quality control inspectors select and test a sample of overload protectors from each shipment. If very few defective units are found in the sample, the lot is probably of good quality and should be accepted. However, if a large number of defective units are found in the sample, the lot is probably of poor quality and should be rejected. The quality control manager requested a producer's risk of 0.10 when po was 0.04 and a consumer's risk of 0.20 when p, was 0.25. Consider the acceptance sampling plan based on a sample size of 15 and an acceptance number of 1. Answer the following questions. (a) What is the producer's risk for the n = 15, c = 1 sampling plan? (Round your answer to four decimal places.) (b) What is the consumer's risk for the n = 15, c = 1 sampling plan? (Round your answer to four decimal places.) (c) Does the n = 15, c = 1 sampling plan satisfy the risks requested by the quality control manager? Discuss. (Select all that apply.) The producer's risk is acceptable since it is less than 0.10. The producer's risk is not acceptable since it is greater than 0.10. The consumer's risk is acceptable since it is less than 0.20. The consumer's risk is not acceptable since it is greater than 0.20. O O O O
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps

Blurred answer
Knowledge Booster
Inventory management
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Practical Management Science
Practical Management Science
Operations Management
ISBN:
9781337406659
Author:
WINSTON, Wayne L.
Publisher:
Cengage,
Operations Management
Operations Management
Operations Management
ISBN:
9781259667473
Author:
William J Stevenson
Publisher:
McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi…
Operations and Supply Chain Management (Mcgraw-hi…
Operations Management
ISBN:
9781259666100
Author:
F. Robert Jacobs, Richard B Chase
Publisher:
McGraw-Hill Education
Business in Action
Business in Action
Operations Management
ISBN:
9780135198100
Author:
BOVEE
Publisher:
PEARSON CO
Purchasing and Supply Chain Management
Purchasing and Supply Chain Management
Operations Management
ISBN:
9781285869681
Author:
Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:
Cengage Learning
Production and Operations Analysis, Seventh Editi…
Production and Operations Analysis, Seventh Editi…
Operations Management
ISBN:
9781478623069
Author:
Steven Nahmias, Tava Lennon Olsen
Publisher:
Waveland Press, Inc.