It is required to calculate the rectangular coordinates of the well from the depth of 10000 ft. to 10400 ft. The kick off point is at 10000 ft. and the rate of build is 0.9 deg/100ft., using a lead of 12 deg. and a right-hand walk rate of 0.9 deg/100ft. Direction of the target is N40E. Assume the first 200ft. is to set the lead, where the direction is held constant to 10200 ft. and then turns right at a rate of 0.9 deg/100ft.

It is required to calculate the rectangular coordinates of the well from the depth of 10000 ft. to 10400 ft. The kick off point is at 10000 ft. and the rate of build is 0.9 deg/100ft., using a lead of 12 deg. and a right-hand walk rate of 0.9 deg/100ft. Direction of the target is N40E. Assume the first 200ft. is to set the lead, where the direction is held constant to 10200 ft. and then turns right at a rate of 0.9 deg/100ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I want an accurate and detailed solution
The pipe of weight W is to be pulled up the inclined plane of slope a using a force P. If P acts at an angle Φ, show that for slipping P = W sin(a + θ)/cos(Φ - θ), where θ isthe angle of static friction; θ = tan-1 μs.
Please solve the given problem with a complete solution. I will upvote. thank you
If the discharge of pipe 4 is 1.4 m³/s, find the amount of water the pump can supply and the pressure head on the pump. Draw the energy grade line and indicate its elevation. El.25m El.13m L3=1230m D3=400mm C =130 Q3 L4=2500m D₁=420mm C =120 E1.0 www L₂=1900m D₂=510mm C =130 L₁=2500m D₁ =610mm C =130 Q4 B El.7m
The answer is given just I don't know how to solve a.) hL=2.55m b.)D=150mm c.)50mm=56.7m, 75mm=8.5m
Follow instructions, box your answers and put a proper units. ANSWER: (a) 1, -4.9 (b) 13/9 (c) 5/9, -4/9 (d) 20/9, -16/9 1.) (a) 9, -4 (b) 13 (c) 5, -4 (d) 20 kN.m, -16 kN.m 2.) (a) 27, -3.56 (b) 56.33 (c) 8.33, -10.67 (d) 60 kN.m, -21.33 kN.m
D=3ft Slope = 151. a Concrete Pipe with a diameter Of 3ft, longitudinal Slope 1.50o, a roughness Valve 0.013. At what Pipe will be given "n" to use For this pipe is depth will the flow rate in the Pipe едиал то 75 cfs? to n=0·013
2-4. A sharp-edged rectangular weir was used to measure the flow of water from a trombone cooler under conditions such that the Francis formula, q = C(L - 0.2H)1 %3D may be applied. cent. The value of L was 8.0 in. with an estimated precision of +0.1 in. H was measured to be 4.0 in., but because of turbulence the precision of this measurement was estimated to be only +0.4 in. (a) What is the "maximum possible systematic error" in the calculated value of q? (b) What is the probable precision of the calculated value of q? (c) Express the calculated value of q in the proper and accepted form. (d) If the weir is to be calibrated at these conditions by collecting and weighing the water which flows over the weir in a period of approximately min, with what precision should the individual measurements be made if the desired precision of q is +0.5 per cent? For q in cubic feet per second and L and H in feet, C 3.33 3 per
A vertical gate keeps water from flowing in a triangular irrigation channel. The channel has a 65 m top width and a 48 m depth. If the channel is full, what is the depth, Yp, of the hydrostatic force on the triangular gate in m? Use the formulas: I. Yp Aỹ h 3 1 -bh3 36 I.
Draw BMD by using (moment distribution method) and check answer by using ( three moment equation)
10:36 .l ? 4 H.we Find ZD, and diraction of flow foo.c006 20 m d:0. ollm 1.5m loml 15m lom A