It is cooled by passing air over the glass plate at 600°C. The heat transfer coefficient is 5 W/ m²K. It is known that the temperature at any point in the glass during the cooling process should not exceed 15°C /mm in order to prevent cracking. If the glass heat transfer coefficient is 1.4 w/mk and the emissivity of the surface is 0.8, what is the lowest air temperature that can be used for cooling at the start-up time? Assume that the air temperature is equal to the temperature of the surrounding surfaces

It is cooled by passing air over the glass plate at 600°C. The heat transfer coefficient is 5 W/ m²K. It is known that the temperature at any point in the glass during the cooling process should not exceed 15°C /mm in order to prevent cracking. If the glass heat transfer coefficient is 1.4 w/mk and the emissivity of the surface is 0.8, what is the lowest air temperature that can be used for cooling at the start-up time? Assume that the air temperature is equal to the temperature of the surrounding surfaces

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.oC) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: a. 361.7 W b. None of these c. 261.7 W d. 303 W
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m.K) or copper (k = 390 W/m-K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials? Aluminum: T = i °℃ Copper: T = °℃ i
A poor heat-conducting copper alloy (k = 45 BTU – ft/hr – ft² – °F) is drawn into 0.012-ft diameter wire for a critical aerospace application in an electronics enclosure. The conditions within the enclosure are maintained at 90°F by a forced air-cooling system. To keep the copper alloy below 270°F and to maximize heat transfer, the wire is to be covered with insulation (k = 0.03 BTU – ft/hr – ft² – °F ). The effective film coefficient for the insulation has been conservatively estimated as 2.0 BTU/hr – ft2 – °F. - - What insulation thickness should be used over the wire to maximize heat transfer? 2.
14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.0C) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: Q2 a. 361.7 W b. None of these c. 261.7 W d. 303 W
based on a large 4 cm thick plate that is initially at a uniform temperature of 20°C that is heated by passing it through a space maintained at 500°C. The plate remains in the space for a period of 7 min. Take the heat transfer coefficient to be 120-W/m2°C. Example 4-4 [k = 110-W/m°C, r = 8530-kg/m³, C, = 0.380-kJ/kg°C, a = 33.9 x 10-6 m²/s] The dimensionless distance from center to a point 0.4-cm below the outer surface is 0.5 0.8 none of the above 0.2
PROCESS INSTRUMENTATION AND CONTROL 4. A 3m X 2m window has an exterior surface temperature of 220C, and the outside wind is blowing air at -60C across it with a convection heat transfer of h= 125W/m2K. What is the total heat transfer loss?
The 10-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m-K) or copper (k = 390 W/m-K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials? Aluminum: T = i °C Copper: T = °C Physical Properties Mathematical Functions
16-90 An electric heater with the total surface area of 0.25 m² and emissivity 0.75 is in a room where the air has a temperature of 20°C and the walls are at 10°C. When the heater consumes 500 W of electric power, its surface has a steady temperature of 120°C. Determine the temperature of the heater surface when it consumes 700 W. Solve the problem (a) assuming negligible radiation and (b) taking radiation into consideration. Based on your results, comment on the assumption made in part (a). We Too, h FIGURE P16-90 Ts Α, ε Qconv Qrad Tw
(B) Cylindrical Water cans (diameter 6.5cm and length 15cm) are to be cooled from initial temperature of 20°C by placing theme in a cooler with ambient temperature of 1°C. Compare the initial cooling rates when the cans are laid horizontally to when the cans are laid vertically. Take v = 15.55x10° m²/s, k=0.024 W/mK and Pr=0.7. Nu = 0.53RA' a4 for horizontal orientation Nu = 0.59 Ra"4 for vertical orientation
Can you help me answer my sample problem for my review?