Answered: Investigate the adequacy of a W310x62…

Investigate the adequacy of a W310x62 to support an axial compressive load of 300 kN dead and 200 kN live on an unsupported length of 5.5 meters. Assume both ends are hinged.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If you don't know the solution please leave it but don't give me wrong solution.
A circular water tank is designed to store water for 78,500 liters capacity. The water tank rests on ground with flexible joints. If M30 concrete and Fe415 steel is used, then what is the maximum hoop tension developed in water tank, if diameter and total height of tank are 5 m and 4 m respectively?
A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
A WT305 x 41 standard steel shape is used to support the loads shown. Assumew= 40 kN/m, LAB = 1.2 m, LBc = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). В LAB LBC LCD WT305 x 41
If the area of cross section of a single angle discontinuous strut is 30cm2 and allowable working stress corresponding to its slenderness ratio is 625 kg/cm², the safe load carrying capacity of the member is (a) 10 tonnes (b)12 tonnes (c) 15 tonnes (d) 18 tonnes
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. 4.0 m po Answers: BC= A 4.0 m BE = EF= i i i B 4.0 m 4.0 m 2.5 m E 12.5 KN 4.0 m kN 2 2 2 kN kN D
The built-up cross-section of the 2.0-m, fixed-base column shown below comprises three 300-mm × 25-mm plates that are welded together. The column is subjected to a 300-kN compressive axial load and moments of 100 kN.m and 50 kN.m about the x and y axes, respectively, at its free end (top). Using Fusion 360, compute maximum tensile and compressive stresses (along z) at mid-height of the column (sufficiently far away from stress concentration zones) and compare them with your hand calculations.\ Answers will be: Cross-section area = 22500 mm2 (5 points) Ix = 453,125,000 mm4 (5 points) Sx = 2,589,286 mm3 (5 points) Iy = 112,890,625 mm4 (5 points) Sy = 752604.2 mm3 (5 points) Stress caused by the axial load = -13.33 MPa (5 points) Stress caused by Mx = ±38.62 MPa (5 points) Max Stress = 91.72 MPa (5 points) Min Stress = -118.39 MPa (5 points)
a) Write and explain one advantage and onedisadvantage of using intermediate stiffeners in plate girders. b) If a plate girder design was initially determined to require intermediate stiffeners, but one optedtonot use them, how else could the plate girder be designed to achieve the same shaer capacity. c) A w-shepe beam is bent in bi-axial bending. All loading passes through its shear center. Please explain why the flexural strenght about its weak axis is the fullplastic moment capacity regardless of Lb
The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft?. Draw the loads with magnitudes on the following structural members: а) BI b) В2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 G1 B3 B2 2 @ 15' = 30' G4 G3 G2 BT 5 @ 6' = 30' 42' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column Cl in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction. OT
A four story "intermediate reinforced concrete moment frames" supports seismic weights of 1400 kip on each floor and 500 kip on the roof. The natural (fundamental) period of this frame as T-0.6 sec. Based on ASCE 7-16 procedures, the base shear this frame must resist in an earthquake is V-846 kip 14 ft 14 ft 14 ft 14 ft A A 7777 7777 777 w=500 kip w=1400 kip w=1400 kip w=1400 kip 7777 1. Based on the natural period, linearly interpolate the value of k that should be used for the equivalent lateral force method. 2. Using your interpolated value of k and the base shear, compute the vertical distribution of lateral loads. 3. Draw an elevation of the frame showing the lateral loads applied to each floor and the roof. 4. Assuming k-2, compute the vertical distribution of lateral loads. 5. Draw an elevation of the frame showing the lateral loads applied to each floor and the roof when k=2.