(i) State whether the frame is in statistically stable equilibrium, and why? (ii) Determine the largest tensile and compressive force anywhere in the frame for this load (by using the method of joints or the method of section ) (ii) If all members have a cross-sectional area of 4000 mm2 and a Young's moaulus of 200 GPa, by how much will these two members change in length due to the applied force? 100 kN 5 m 100 kN 20m (4 x 5m)

Q: A bedroom has a volume of 126 m3m3 . What is its volume in decimeters cubed (dm3dm3)?

A: Given data- The volume of the bedroom = 126 m3 To Find- The volume of the bedroom in decimeters…

Q: 3. You wish to lift a 12,000 lb stone by a vertical distance of 15 ft. Unfortunately, you can only…

A:

Q: C. Put the following words related to roads, bridges and waterways (barrage, pavement, dam, curb,…

A: Roads i) Pavements ii) Curb iii) Pedestrian crossing   Bridge  i) Aqueduct  ii) Deck iii) Barrage…

Q: What is the relation between head loss due to friction and flow velocity?

A: The losses in the pipes are categorized into two types, those are major loss and minor loss. The…

Q: Q:  (i) How to orient a hospital building so that it can get maximum natural light and ventilation.…

A: (1)- The building of hospital should be aligned in east direction as much as possible for maximum…

Q: What is kinematics? What is meant by pitch, yaw and roll?

A:

Q: Describe Basic Hydrogeology.

A: Hydrology is the science which handles the Earth's waters, their occurrence, circulation and…

Q: What is susbtainable design?

A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…

Q: What is the rate of flow of water a pipe with a radius of 10mm and speed of 500mm/sec?

A: Radius of pipe (r) = 10 mm  Velocity of flow (V) = 500 mm/sec  Determine the flow rate of the water…

Q: Draw the complete shearing force diagram and bending moment diagram for the beam shown below. State…

A: A beam is simply supported at two ends. Two UDLs of 500 N/m at each end 0.3 m from the supports A…

Q: What is shear starin rate?

A: Shear rate:

Q: Distinguish between intermittent system and continuous system of water supply

A: In Intermittent system water supply is divided into several zone and each zone is supplied with…

Q: Determine its classification using USCS.

A: USCS Soil classification:

Q: delermine wether G) is analytic ornot.

A:

Q: (Figure 1) Express your answer with the appropriate 0 Submit μA 6 a 1₂= 26.268 108 mm Previous…

A:

Q: Differentiate force system based on line of action.

A: A force is a push or pull on an object caused by its interaction with another object.

Q: what is mercury manometer? own words

A:

Q: Q/Classification the water tanks according placement?

A:

Q: What do you mean by make-up airflow rate?

A: Air enters a building of the quantity nearing the exhaust flow rate whether or not provision is made…

Q: Explain the concept of "float."

A: Answer IntroductionThe float generally used for finding the critical path in the project management…

Q: A- In Fig.A , If the resultant force acting on the bracket is to be 642 N directed along the…

A: (A) in Fig AHorizontal force component of 300 KN force =300×cosθθ is the angle of force with…

Q: What is the use of a magnetic needle?

A: Magnetic needle The magnetic needle is used in compasses that are magnetic in nature.

Q: Discuss  in  details coagulation

A: Coagulation is defined as the process of converting smaller dissolved solids into larger particles…

Q: May I trouble you to solve the problem (b)

A: Find: The reactions at the supports and draw the bending moment diagram.

Q: Give a list of some typical situations where ageotechnical instrumentation program is required ?

A: Situations where a geotechnical instrumentation program is required: when Tunnels, boreholes,…

Q: Do the demands of a user vary from those of a system?

A: User access security refers to integrated processes where authorized users have access to a computer…

Q: List some benefits of using hand-level instruments.

A: A hand level instrument is a device which is used  for rough levelling.  It is mainly used for small…

Q: Organize the ten (10) scrambled words given and create a horizontal network diagram that shows the…

A: ACTIVITY                                                                             PREDECESSOR…

Q: What should be included in the list of the equipment?

A: - List of equipment is a type of list which includes all type of electrical equipment and mechanical…

Q: Define what are Instrumentation Devices ?

A: Answer IntroductionInstrumentation device is known as the device which is used to measure the…

Q: Define the term diffusivity ?

A: The answer is below:

Q: What are Frontal Inversions?

A: Inversion is used when metrological inversion of temperature takes place. It is an alteration from…

Q: What are servomotors?

A: Servomotors are used in cars to control its speed.

Q: Explain the difference between average and instantaneous speed.

A: The overall distance traveled by the object in a given time frame is the average speed. A scalar…

Q: How does backwashing a filter in water treatment cause head loss. Please explain

A: Backwashing a filter in water treatment causes head loss due to the rearrangement of filter media.…

Q: What is Constructive Acceleration?

A: The constructive acceleration is defined as “when a failure occurs the contractor accelerates the…

Q: what is cirque water pumps

A: A cirque water pump, also known as a circulating pump, is a type of closed-circuit pump that…

Q: Question: Give three (3) examples of the everyday use of pneumatic. Note: -NO PLAGIARISM PLEASE.…

A: A pneumatic system is a group of interconnected components that use compressed air to do work for…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.