Instructions: solve the following problem below. Show your complete Solutions, corresponding figures, illustrations and dimensions, without the following points will be deducted. 1.) Determine the Compressive capacity of an A36 W460X97 steel section. If No brace and k, 1.0 and ky = 0.7 а. i. L = 3.5 m ii. L = 2.0 m iii. L = 1.5 m b. Braced in the middle of the x-axis with k, = 1.0 and braced at the middle third of the y- axis with ky = 0.7 i. L= 3.5 m ii. L = 2.0 m iii. L = 1.5 m Use only NSCP 505.3

Instructions: solve the following problem below. Show your complete Solutions, corresponding figures, illustrations and dimensions, without the following points will be deducted. 1.) Determine the Compressive capacity of an A36 W460X97 steel section. If No brace and k, 1.0 and ky = 0.7 а. i. L = 3.5 m ii. L = 2.0 m iii. L = 1.5 m b. Braced in the middle of the x-axis with k, = 1.0 and braced at the middle third of the y- axis with ky = 0.7 i. L= 3.5 m ii. L = 2.0 m iii. L = 1.5 m Use only NSCP 505.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w = 2.2 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and Lcp = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. P B LAB LBC Answer: Omax tel i |C * ksi W LCD X
Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. O 212 kip O 202 kip O 196 kip 224 Wip
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
11. B.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 23 kips, w = 4.2 kips/ft, LAB = 3.4 ft, LBC = 3.4 ft, and LcD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. B |C LAB LBC LCD Answer: Omax = ksi
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Please help me with my homework and use ASEP STEEL HANDBOOK 2004 volume 1 Dimensions and Properties Third Edition, to find the AISC. PLEASE SHOW COMPLETE SOLUTIONS AND DETAILS.
Problems 6 - 7: Design the following sections by finding As and A's. Mu is provided below the figure. Use fy = 60,000 psi, f'c = 4000 psi. Start the design by verifying that compression steel is needed to meet the required strength. Once you have calculated A, and A's, select bar size and # using the tables, then show that the actual resultant steel areas satisfy the design requirements listed below: 14" Use Mu =900k-ft capacity: Mn > Mu/ ductility: &t >= 0.005 (note: it is not required that &'s > 0.00207) minimum steel: As > As,min 3" 23" 3" stut. * 10" 8" 8" Use Mu=300k-ft 3" 14" 3"
The Aluminum plates below are connected by two 3/4" diameter bolts. What is the shear stress in the bolts given the load applied?
B4
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks