In the solid circular section bar with radius R=10mm in the figure, due to the given loading, Find the cross-sectional effects at point A, Draw the normal stress distribution oz on the section, Draw the shear stress distribution t on the section. A 5. X m B P= 12 kN Q = 1Y kN 2m X-7 Y=1 Z=0

In the solid circular section bar with radius R=10mm in the figure, due to the given loading, Find the cross-sectional effects at point A, Draw the normal stress distribution oz on the section, Draw the shear stress distribution t on the section. A 5. X m B P= 12 kN Q = 1Y kN 2m X-7 Y=1 Z=0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The articular Cartilage is subjected to plane stress with normal stresses ox , o, and shear stress Txy, as shown in the figure. At a counterclockwise angle e = 30° from the x-axis, the normal stress is 3 MPa tension, and at an angle e = 50°, it is 2 MPa compression. Find the principals stresses. Ty 0, =10 MPa
A single-piece bicycle crank is shown below under the following load: the rider pedals forward with a vertical force Fp = 500 N on the left pedal and no force on the right pedal. The chain exerts a force Fc on the chainring. The spindle is a solid cylinder with a diameter d = 16 mm. 1. Find the maximum normal stress and shear stress at cross-section y-y in image. Indicate the locations on the given cross section view where they act.
A circular aluminum tube with a length of L = 420 mm is loaded in compression by forces P (see figure). The hollow segment of length LB has outside and inside diameters of 60 mm and 35 mm, respectively. The solid segment of length 2L/3 has a diameter of 60 mm. A strain gage is placed on the outside of the hollow segment of the bar to measure normalstrains in the longitudinal direction.(a) If the measured strain in the hollow segment is6jy=470*10 , what is the strain in the solid part? Hint: The strain in the solid segment is equal to that in the hollow segment multiplied by the ratio of the area of the hollow to that of the solid segment.(b) What is the overall shortening of the bar?(c) If the compressive stress in the bar cannot exceed 48 MPa, what is the maximum permissible value of load P?
Athin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = y i b Q S a X urad
Try One scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN, determine the force components perpendicular (N) and parallel (V) to a – a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a – a. 90 mm 62° a N kN kN Aa-a mm2 P = 80 kN MPa MPа Try one 1st 2nd 3rd Enter attempt
State of stress at the wall and the roof of the following circular opening bafore the excavation is (a] = |0 4. Find the induced stress components at point a. R W with respect to the given x-y coordinate systerm, and expresst them in the matrix form. b. Find the total stresses at point W, and give them in matrix form. c. Repeat (a) and (b) for the roof. d. Find the stresses oy, Ciy, and tyy at point A which is located at a radial distance twice the radius of the tunnel.
A cable is enacting a force, F, on a built-in hook at an angle 9 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. If E= 200 GPa, F = 50 kN, 0 = 25°, L = 1 m, r- 100 mm: Answer: 8 = 0.196 mm
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
H K T A solid shaft is subjected to forces and a torque as shown in figure. The diameter of the shaft is 35 mm, T=75 N.m., V=3 kN, P=4,7 kN and L=117 mm. Determine the shear stress (T) at point H (MPa). Note: If the stress has negative direction, use sign. Yanıt:
Strain gage Problem 1.6-4 A circular aluminum tube of length L-600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d;-75 mm and di-63 mm, respectively. A strain gage is placed on the outside of the tube to measure normal strains in the longitudinal direction. Assume that E- 73 GPa and Poisson's ration v 0.33. 1- 7- (a) If the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e 781 x 10, what is the shortening Sof the tube? What is the percent change in its cross-sectional area? What is the volume change of the tube? (c) If the tube has a constant outer diameter of d, -75 mm along is entire length L but now has increased inner diameter d, with a normal stress of 70 MPa over the middle third, while the rest of the tube remains at normal stress of 57 MPa, what is the diameter d,? 41 dz 13- (b)
(3): A steel bar ABCD (4m) long is subjected to forces as shown in Figure. Find the stresses in each part. d=20 mm d=15 mm d=15 mm В D 20 kN 25 kN 5 kN 10 kN (4): A round tapered alloy bar (4m) long is subjected to load as shown in Figure. Find the stresses in section at point (B) and section at point (C). D B 30 kN. 50 kN 70 kN 50 kN d=20 mm d=40 mm 1m 2 m 1m
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.