A cable is enacting a force, F, on a built-in hook at an angle 8 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. AT

A cable is enacting a force, F, on a built-in hook at an angle 8 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. AT

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4–3. The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. *4–4. Determine the displacement of B with respect to C of the composite shaft in Prob. 4–3.
i need the answer quickly
3. Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8. Find the maximum shear stress in each shaft. Diameter A C = 30 cm Diameter CB = 20cm 0.5cm 1 cm
Athin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = y i b Q S a X urad
Mo = M-400×0.15cos30-320x 0.3 = 0 160 mm 400 N M = 148 Nm CCW Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm 250 mm 125 mm 240 N
A motor delivers a power of 79 W to a pump. If the impeller at point B is rotating at a frequency f = 166 rev/min. What is the maximum shear stress in the 29-mm-diameter transmission shaft at A? f (rev/min)
For the system below , find the maximum stress for the member ECD due to the combined effect of axial and bending moment .
A hydraulic punch press is used to punch a slot in a 0.30-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 36 ksi, determine the minimum force P required to punch the slot. Assume d = 1.25 in. and a = 2.25 in.
5. A 4-point bending test is performed on a beam of length L = 1 m. A load of P = 2000 N is applied across two loading points a distance a = 0.4 m from the sides of the beam. If the beam has a radius of r = 1 cm and a yield strength of σ = 250 MPa, does the bar yield? If it's an elastic-perfectly plastic material, does it fail all the way through the thickness of the bar? What would the yield strength of the material need to be if we wanted a factor of safety of 1.5?
The solid shaft of radius c is subjected to a torque T at its ends. Show that the maximum shear strain in the shaft is gmax = Tc>JG. What is the shear strain on an element located at point A, c>2 from the center of the shaft? Sketch the shear strain distortion of this element.
A turning force of 4 kN parallel to the "y" axis will be applied at the C point of the arm connected to the steel shaft AB in the figure. Accordingly, find the safe diameter value of the AB shaft using TRESCA and VON-MISES criteria.
The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 290 N causes the upper frame to be deflected downward by d = 8.5 mm. Determine the average shear strain in the rubber blocks. P 0.488 rad O 0.563 rad 0.517 rad O 0.348 rad O 0.315 rad Double U anti-vibration shear mount 16 25 Rubber block dimensions Shear deformation of blocks 22