A thin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. y yek Y = P i b 2 S T x urad

A thin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. y yek Y = P i b 2 S T x urad

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2. A braces wire is used in tension to press the teeth to P put it on their place. If the wire have a diameter of 0.03 in, initial length of l, = 10.16 cm in normal strain ɛ = 500 x 10-4 and stress o = 3000 psi. Find the elongation of the wire and load. A.
Problem 10 Problem 8.3-5 A strain gage is installed in the longitudinal direction on the surface of an aluminum beverage can (see figure). The radius-to-thickness ratio of the can is 200. When the lid of the can is popped open, the strain changes by E, = 170 x 10-. What was the internal pressure p in the can? (Assume E = 10 x 10° psi and v = 0.33.) Soda Pop
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.7 mm and upward by v = 3.5 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 720 mm, a = 31% and 3 = 59° Answer: y = i P R urad
PROBLEM 4. A piece of rubber, which was originally a square shape, has been deformed into a shape shown with the dashed lines in the figure. After the deformation, the CD line remained parallel to the direction before the deformation. (a) Calculate the average normal strains along AB and diagonal AD. (b) Calculate the average shear strain yxy at point A. 6 mm 84 mm 4 mm 80 mm 2 mm 80 mm mm
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. h ΫΠ' ΑΣΦ D The diameter of the bar is d = 230 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 40 mm from the bottom of the bar if the radius of curvature is measured to be p = 6.7 m? Express your answer to three significant figures. ► View Available Hint(s) Ax ↓↑ vec t O ? mm/mm
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.8 mm and upward by v = 5.6 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 620 mm, a = 26°, and B = 64° Answer: y = i P a B R urad
A steel wire with a diameter of d = 1/16 in. is bent around a cylindrical drum with aradius of R = 36 in. (see figure).a. Determine the maximum normal strain emaxb. What is the minimum acceptable radius of the drum if the maximum normalstrain must remain below yield? Assume E = 30,000 ksi and ey= 100 ksi.If R = 36 in., what is the maximum acceptable diameter of the wire if the maximumnormal strain must remain below yield?
Strain gage Problem 1.6-4 A circular aluminum tube of length L-600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d;-75 mm and di-63 mm, respectively. A strain gage is placed on the outside of the tube to measure normal strains in the longitudinal direction. Assume that E- 73 GPa and Poisson's ration v 0.33. 1- 7- (a) If the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e 781 x 10, what is the shortening Sof the tube? What is the percent change in its cross-sectional area? What is the volume change of the tube? (c) If the tube has a constant outer diameter of d, -75 mm along is entire length L but now has increased inner diameter d, with a normal stress of 70 MPa over the middle third, while the rest of the tube remains at normal stress of 57 MPa, what is the diameter d,? 41 dz 13- (b)
Incorrect A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ 12 d d₁ Undeformed Answer: dos = i 9810.3 R Calculate the deformation of diagonal QS. Deformed X mm
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. The diameter of the bar is d 180 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 30 mm from the bottom of the bar if the radius of curvature is measured to be p Express your answer to three significant figures. ▶ View Available Hint(s) £= - ΠΙΑΣΦ vec ? Ax mm/mm 5.4 m?
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0550-in. to new position Q'as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 16 in., b = 9 in., c = 12 in., and A = 0.0550 in. a R A Q' Answer:y = i prad