Q# 3 A rectangular plate in biaxial stress (seefigure) is subjected to normal stresses 0,=100MPa (tension) and 0,=20 MPa (compression).The plate has dimensions 200 x 400 x 10 mm6and is made of steel with E = 200 GPa and v= 0.30.(a) Determine the maximum in-plane shearstrain Ymax in the plate. (b) Determine thechange At in the thickness of the plate. (c)Determine the change AV in the volume of theplate.

Given: The normal stress in the x-direction is бx= 100 MPa. The normal stress in the y-direction is…

Q # 3 A rectangular plate in biaxial stress (see figure) is subjected to normal stresses 0,=100 MPa (tension) and 0,=20 MPa (compression). The plate has dimensions 200 x 400 x 10 mm and is made of steel with E = 200 GPa and v = 0.30. (a) Determine the maximum in-plane shear strain Ymax in the plate. (b) Determine the change At in the thickness of the plate. (c) Determine the change AV in the volume of the plate.

Q # 3 A rectangular plate in biaxial stress (see figure) is subjected to normal stresses 0,=100 MPa (tension) and 0,=20 MPa (compression). The plate has dimensions 200 x 400 x 10 mm and is made of steel with E = 200 GPa and v = 0.30. (a) Determine the maximum in-plane shear strain Ymax in the plate. (b) Determine the change At in the thickness of the plate. (c) Determine the change AV in the volume of the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin-walled cylindrical pressure vessel of inner radius r = 0.6 cm and a thickness of 0.06 cm is subjected simultaneously to internal gas pressure p = 3.5 MPa, a compressive force F = 800 N acting at the ends, and a torsional load of 25 N · m (see figure). Determine the following quantities (a) the principal stresses at a point H on the surface of the vessel and the absolute maximum shear stress; (b) the normal strain along x-axis (ɛx) and the shear strain (yxy) at the same point H. See the established Oxy coordinate system. The Young's modulus of the material is 200 GPa and the Poisson's ratio is 0.3. Hint: the cross-section of the vessel can be regarded as a hollow tube and the cross-section area can be calculated as 1(0.00662 – 0.006²). You can do the same treatment for the polar moment inertia. 25 N· m F F H X 25 N· m
The articular Cartilage is subjected to plane stress with normal stresses ox , o, and shear stress Txy, as shown in the figure. At a counterclockwise angle e = 30° from the x-axis, the normal stress is 3 MPa tension, and at an angle e = 50°, it is 2 MPa compression. Find the principals stresses. Ty 0, =10 MPa
Answer quickly
A circular aluminum tube of lengthL = 600 mm is loaded in compression by forces P(see figure). The outside and inside diameters ared2 = 75 mm and d1 = 63 mm, respectively. A straingage is placed on the outside of the tube to measurenormal strains in the longitudinal direction. Assumethat E = 73 GPa and Poisson’s ratio is n = 0.33.(a) If the compressive stress in the tube is 57 MPa,what is the load P?(b) If the measured strain is ε =781x10 -6 , what isthe shortening δ of the tube? What is the percent change in its cross-sectional area? What is thevolume change of the tube?(c) If the tube has a constant outer diameterof d2 = 75 mm along its entire length L butnow has increased inner diameter d3 with a normalstress of 70 MPa over the middle third (seefigure, part b) while the rest of the tube remains atnormal stress of 57 MPa, what is the diameter d3?
Athin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 1.6 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = y i b Q S a X urad
i need the answer quickly
Angle a=36 Angle b=53 The tolerance is ±1%
Incorrect A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ 12 d d₁ Undeformed Answer: dos = i 9810.3 R Calculate the deformation of diagonal QS. Deformed X mm
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition, (i) determine the normal and shear stress acting on the inclined plane (ii) calculate the principle angle and the shear angle
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0550-in. to new position Q'as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 16 in., b = 9 in., c = 12 in., and A = 0.0550 in. a R A Q' Answer:y = i prad
0.19