In the refrigeration experiment, the following values were measured when using the TXV valve (the TXV valve has been calibrated for a superheat temperature of 5C)°: 1- Temperature at the compressor outlet: 94.7±0.5°c 2- Absolute pressure at the valve inlet: 1150± 40 kPa 3- Absolute pressure at the valve outlet: 260± 10 kPa What is the error in the enthalpy of the refrigerant leaving the condenser in units of kJ/kg? Use at least 2 significant digits when you fill in your answer. NOTE: Assume that the quality at the exit of the condenser is exactly zero with no error.

In the refrigeration experiment, the following values were measured when using the TXV valve (the TXV valve has been calibrated for a superheat temperature of 5C)°: 1- Temperature at the compressor outlet: 94.7±0.5°c 2- Absolute pressure at the valve inlet: 1150± 40 kPa 3- Absolute pressure at the valve outlet: 260± 10 kPa What is the error in the enthalpy of the refrigerant leaving the condenser in units of kJ/kg? Use at least 2 significant digits when you fill in your answer. NOTE: Assume that the quality at the exit of the condenser is exactly zero with no error.

Name: In the refrigeration experiment, the following values were measured w
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: In the refrigeration experiment, the following values were measured when using the TXV valve (the TXVvalve has been calibrated for a superheat temperature of 5C)°:1- Temperature at the compressor outlet: 94.7±0.5°c2- Absolute pressure at the valve i

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermofluid Engineering
COMPLETE SOLUTION. FINAL ANSWER ARE IN ENGLISG SYSTEMS. DRAW A DIAGRAM IF NECESSARY. Engine XYZ is designed to be operated on the following temperature limits: 80 deg Fahrenheit and 750 deg Fahrenheit. At the beginning of the isothermal expansion the pressure is 350 psia and at the end of the isothermal expansion the pressure is 190 psig. Determine (a) the volume at the end of the isothermal compression, (b) the change of entropy during an isothermal process, (c) the heat added and the rejected, (d) the thermal efficiency, (d) the work developed in BTU/s, and (e) the mean effective pressure.
Class Task 2.1 2.2 2.3 2.4 2.5 A two-stage, single-acting air compressor with a polytropic index of 1.35 runs in an atmosphere with free air conditions at 87 kPa and 20 °C. It has a FAD of 4 m³/min with a delivery pressure of 1 MPa. Induction occurs at 80 kPa and 30 °C. The mechanical and motor-drive efficiencies are 80% and 90% respectively. Assume complete inter-cooling and neglect clearance volumes. Draw a P-V-diagram to illustrate the operation of the two-stage compressor and assign relevant numbers. Mention 2 consequences of imposing Perfect Intercooling as a pre-requisite condition in multistage compression. Calculate: The intermediate pressure, The temperature of the air at entrance to the intercooler, The rate of heat rejected in the intercooler (kW), The input power from an electric motor. C
A single effect evaporator was used to concentrate 8000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the Evaporator at 20 ° C. The evaporator is operated on Steam (80% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). Count it (a) Steam demand rate = Answerkg / hour. b. Steam economy when condensate temperature is released at 75 ° C. = Answer(kg of water evaporated / kg of steam)
Question Three Air flows steadily adiabatically through a pipe with a constant cross-sectional area. Air is fed into the pipe through an isentropic converging nozzle from a large tank where the pressure and temperature are 900 kPa and 300 K, respectively, as shown in the figure below. The pressure at the inlet of the duct is 750 kPa. If the temperature at the duct exit is 275 K, determine the pressure at the duct exit. Ans. pe = 568.7 KPa
A supply line carries a two-phase liquid–vapour mixture of steam at 450 psi. A small fraction of the flow in the line is diverted through a throttling calorimeter and exhausted to the atmosphere at 20 psi. The temperature of the exhaust steam is measured as 350°F. Determine the quality of the steam in the supply line. Select one: a. 95.7% b. 98% c. 92% d. 100%
Refrigerant 134a: T = 20°C v = 0.05397 m/kg O On the Triple Line Saturated Vapor Saturated Liquid Critical Point Superheated Vapor Compressed Liquid
STEAM PROCESSES
Saturated steam at P1=25 bar expands adiabatically through a throttling valve to P2=4 bar. If the quality of the steam at the valve inlet is x1=0.9 what is the quality x2 at the valve outlet Please respond ASAP
A four stage single acting air compressor running in an atmospheric at 87 KPa and 15 degrees Celsius has a free air delivery of 2,83 m³/min. The section pressure and temperature are 80 KPa and 32 degrees Celsius respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 degrees Celsius, take n=1.3 for all stages. Calculate : 1. The intermidiate pressure ratio in 3 decimal place 2.The intermidiate pressure at first, second and third stage in KPa 3. The mass flow rate in kg/min 4.The power input in KW
Can there be an psychological component to mechanical ventilator dependence? If so, what factors contribute to the dependence?
9 thermodynamics