A rigid tank contains air at 550 kPa and 190 °C. As a result of heat transfer to the surroundings, the temperature and pressure inside the tank drops to 85 °C and ?420 kPa, respectively. What is true about boundary work for this problem Wp will be maximum .1 Wb will be negative .2 Wb = .3 None 4 O

A rigid tank contains air at 550 kPa and 190 °C. As a result of heat transfer to the surroundings, the temperature and pressure inside the tank drops to 85 °C and ?420 kPa, respectively. What is true about boundary work for this problem Wp will be maximum .1 Wb will be negative .2 Wb = .3 None 4 O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: You have an ideal gas in an insulated container. You compress it from a pressure of 40 × 105 Pa to 20 × 105 Pa, while increasing the volume from 10 to 20 m3. What is the work you done by the gas a- 10 J b- 300 J c- 500 J d- 880 J
ft-lb 7. One pound of air R = 53.3 is compressed isothermally in a closed system from ib-R 15 psia and 80°F to 90 psia. Compute the heat transfer.
There is 3.5 L saturated liquid water at 175 kPa pressure in the frictionless moving piston-cylinder system shown in the figure. The heat given to the system is 500 kJ and the electrical work is 1320 kJ. Since half of the water evaporates at constant pressure; a) Write the energy balance equation (First Law), b) Calculate the mass (kg) of water, c) Calculate the required shaft work (kW), d) Show the process in T-v and P-v diagrams, including saturated liquid and saturated vapor curves
1. An irregular container, closed at the end, is filled with water (999 kg/m). Consider the opening exposed to the atmosphere at 1 atm, find the pressure at point A. Refer to the figure below. P. atm 0.5 m, 40° 60° 0.4 m 0.4 m 3 m 3 m 2.6 m А. 0.3 m all in meters 0.5 0.5 0.5 2.7 m- 1 m
Edición P3. A piston-cylinder system contains 1 L of water at 105°C and 85% quality. I know adds energy, causing the plunger to travel until it makes contact with a spring of constant K = 100 N/mm, just at this moment, the volume of the water is 50% greater than the initial. The energy transfer continues until the volume is 1.7 L, and the temperature of the water reached 600°C. Make a schematic of the system according to the statement and calculate the water pressure when T = 600°C. Answer: 198.16kPa
A gas compressed according to the law PV1.5 = constant from the initial pressure and temperature of 105 kN/m? and 26 °C respectively to a pressure of 900 kN/m² .The gas is then cooled at constant pressure, then the gas was expanded isothermally to the initial conditions. Take y= 1.5.
Graw 1 Q A The force generated by a spring is given by F= kx where k is the spring constant, and x is the deflection of the spring. The spring shown in the figure has a spring constant of 9.5 kN/cm. The pressures are P-5000 kPa, P₂=10000 kPa, and P3 = 1000 kPa. If the piston diameters are D=8 cm and D2-3 cm, how far will the spring be deflected? Z Spring- The spring will deflect 1.717 cm. 2 W D₁ S 309 F2 X #3 E D 80 F3 $ 4 C 888 F4 R 25 % V MA FS T U N * 00 8 J DII - M ( 9 K DD F9 O ) V S 0 J L T' P
Q2) Find: (a) initial pressure (P =?), (b) final temperature (T2 =?), (c) the amount of heat added to the system, (d) plot T-v and P-v diagrams. Water: m = 2 kg V = V2 = 300L Qin =? T = 120°C P2 = 1.8 MPa
A container will break when the gauge pressure within it reaches 520 kPa. It is attached to the lower end of a vertical pipe, with the pipe and the container filled with liquid (? = 890 ? ?? 3 ). How long can the pipe be if the container is not to break?
A spherical research balloon is filled with 420 m3 of atmospheric air at atemperature of 10 oC. If the air inside the balloon is heated to 80 oC accordingto PVn =C, where n = 0. What will be the final diameter of the balloon?
A frictionless piston/cylinder assembly A shown in the figure is connected by a thin pipeline with a valve to a rigid tank B. The volume of tank B is 1.0 m³, and the cross-sectional area of the piston is Aa = 1.2 m?. Initially (state 1) the valve is closed, 3 kg of argon is enclosed in the piston/cylinder assembly, mĄ1 = 3 kg, and there is no argon in the tank, mg,1=0. The initial temperature of the argon is TĄ1 = 50°C and the initial volume of the gas enclosed by the piston cylinder is VA1 = 1.5 m?. The valve is slowly opened allowing argon to flow into the tank. The valve is then closed when the piston just touches the stops but does not exert a force on the stops (state 2). At state 2, the temperature and pressure throughout the tank and piston/cylinder system are equal (Pa2 = P8,2 and Ta2= T82). The height from the bottom of the cylinder A to the top of the stops is htops = 0.5 m. The volume of the stops can be assumed negligible. Treat argon as an ideal gas. a) Determine the…