In the illustration: A 1 C All friction factor f = 0.02 All pipe lengths L = 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.

In the illustration: A 1 C All friction factor f = 0.02 All pipe lengths L = 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A swimming pool is 10 ft wide and 20 ft long and its bottom is an inclined plane, the shallow end having a depth of 3 ft and the deep end, 7 ft. Assume the pool is full of water. (Round your answers to the nearest whole number. Recall that the weight density of 62.5 lb/ft³.) (a) Estimate the hydrostatic force (in lb) on the shallow end. 2813 lb (b) Estimate the hydrostatic force (in lb) on the deep end. 15313 (c) Estimate the hydrostatic force (in lb) on one of the sides. (d) Estimate the hydrostatic force (in lb) on the bottom of the pool.
Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter pipe through a vertical reducer bend. The change in water direction of the reducing bend is 120o. The vertical distance between the entrance and outlet of the bend is 1.5 m and the pressure at its entrance is 70KPa. The total weight of the bend material and water contained in it is 90 kg. Sketch the forces involve in the pipe flow analysis
Try to solving these problems: 1. Water at A has a pressure of 400 kPa and a velocity of 3 m/s. Determine the pressure and velocity at B and C. 150 mm 3 m/s 100 mm 50 mm B
i)Calculate the flow rate through the system.
Three reservoirs A, B and C are connected by a pipe system shown in the figure below. If the rate of flow from the reservoir A is 55 l's, and the coefficient of friction (F) for all pipes is 0.015. Find the piezometric head at point D A L2=600 m d2=20 cm D Q1=0.055 m/s L1=1200 m d1=30 cm 28 m 30 m
Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B в is 87 kPa, estimate the pressure at A, in kPa. Assume all fluids are at 20°C. ywater =9790 N/m', Ymercury =133100 N/m2, yoil =8720 N/m³ SAE 30 oil Gage B Mercury 6 cm 5 cm Water flow 11 cm 4 cm
μ=0.20 6. For the given system, the cylinder of mass m is attached to a frictionless pulley. The chord attached to the 60.0 kg block runs through the fixed drum with coefficient of friction equal to 0.25. The coefficient of friction between the block and the incline is 0.15 and the coefficient of belt friction is 0.20. Determine the range of mass m so that the system remains at rest. μ-0.15 20⁰ m Solution guide: . Consider Case 1: the motion is impending down the plane. o What are the forces acting on the 60 kg block? o What is the direction of friction force? o Calculate the tension force acting on the block. Is this the heavier tension or the weaker tension? Consider Case 2: the motion is impending up the plane. o What are the forces acting on the 60 kg block? o What is the direction of friction force this time? o Calculate the tension force acting on the block. Is this the heavier tension or the weaker tension? Answer: 16.4348 kg ≤m ≤85.0868 kg 60 kg
ROVINCE c). If the viscosity is 0.0126 stokes, what is the equivalent kinematic viscosity in m2/s? 3. If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump, a) what will be the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b) how much power is required to drive it if the diameter of the suction side is 600 mm? c) If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system? STATE 1969
Example 2 What fraction of the mass flow rate m is diverted down the plate shown below? Neglect friction between the water and the plate and the effect of gravity. Calculate the force F required to hold the plate stationary. V2 solution: V = 30 m/s Water in the x-direction F = M - M, in out m=5kg/s But F, =0 → M, out - M, in = V,m, - V,m, = V,m, -V,(m– m,) 45° M. x out M, in = V, cos 45m
Q- In a pond at a depth of 5m air bubble is formed of diameter 0.8mm. Calculate gauge pressure inside air bubble. Assume surface tension = 0.075N/m.
Oil (µ = 0.35 Pa-sec) flows through a horizontal 20 cm diameter circular pipe. The velocity at any point in the pipe’s cross-section a distance at a distance y from the center is: V =64(r² − y²) / μ where: r = 10 cm (radius of the pipe) Determine the following: a) Maximum flow velocity (m/sec) b) Shear stress (Pa) at the pipe’s centerline c) Shear stress (Pa) at the pipewalls?
7. As shown in the figure below, a pump lifts water through a 100-mm diameter ductile iron pipe (friction factor f = 0.0251) from a lower to an upper reservoir. If the difference in elevation between the reservoir surfaces is 10m, and the pump performance curve is given by H = 15 - 0.1Q2, where H is in m and Q in L/s. (1) Determine the system head curve (relationship between TDH and Q) assuming the entrance and exit loss coefficients are both 1; (2) Estimate the flow rate through the system; (3) If the minimum NPSH for this case is 1.5m, determine the maximum height above the lower reservoir that the pump can be placed (assuming that the atmospheric pressure Pa=101 kPa, specific weight of water γ = 9.79 kN/m3, and the water vapor pressure Pv = 2.34 kPa).