**Problem Statement:**In the frame shown below, what is the value of the vertical reaction force component at C? *(Note: Enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for down.* Vertical force component at C, Cy = _____________ N**Diagram Explanation:**The diagram shows a frame structure with three main points: A, B, and C. - Point A is at the left end, attached to the ground at a 60-degree angle, with a distance of 3 meters between A and B.- Point B is a pivot point, situated between A and C.- Point C is at the right end, connected to the ground.- There is a horizontal beam connecting points B and C, with a length of 4 meters (2 meters from B to a mid-point, and another 2 meters from the mid-point to C).- A vertical force of 2000 N acts downward at the mid-point of the horizontal beam.The task is to determine the vertical force component at point C (Cy).

-↺ΣMc=0 :- FAB sin 60 x4-2000 x 2=0 FAB=1154.7N e →compression

In the frame shown below, what is the value of vertical reaction force component at C? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for down. Vertical force component at C, Cy = 2000 N C B. 3 m 2 m 2 m- 60°

In the frame shown below, what is the value of vertical reaction force component at C? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for down. Vertical force component at C, Cy = 2000 N C B. 3 m 2 m 2 m- 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The matrix approach needs to be used to solve for the joint displacements, reactions, and member end forces. Perform calculations in units of k and in. I sincerely need help on how to figure this out.
The collar has a mass of 3 kg and travels along the smooth horizontal rod defined by the equiangular spiral r = (e) m, where 0 is in radians. (Figure 1) Figure 0 F r = e A Part A Determine the tangential force F and the normal force N acting on the collar when = 40°, if the force F maintains a constant angular motion = 1.5 rad/s. Express your answers in newtons to three significant figures separated by a comma. ► View Available Hint(s) F.N= ΨΕΙ ΑΣΦ | Η Submit Previous Answers vec 3 ➜ O X Incorrect; Try Again; 3 attempts remaining Cred ? Review N
А C a Given a cantilever beam with a concentrated force P at point B. What is the maximum deflection of the beam in millimeters? P= 18 kN a = 2.8 m b = 4.7 m El = 80,000 kN-m^2 Do not write the units! Any number of decimal places is OK. P.
Determine the slope and vertical displacement of point A on the beam shown in the accompanying illustration. Use Conjugate Beam Method. E = 200,000 MPa
only HANDWRITTEN answer needed ( NOT TYPED)
Determine the shear force and moment acting at point C of the beam shown in (Figure 1). For the calculation use Simpson's rule to evaluate the integrals. Follow the sign convention. Figure W 2 kip/ft w = (2x³ + √√x + 4)"> 2 ft 2 ft 1 of 1 11.58 kip/ft Part A What is the shear force at C? Express your answer in kilopounds to three significant figures. Vc = Submit Part B 15. ΑΣΦ Request Answer vec Beste ? What is the moment at C'? Express your answer in kilopound-feet to three significant figures. kip
Question 21 3.5 m A C 5.5 m 0.2 m X B D G A Time left 0:58:42 In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 5.7 m, and the load D has a mass of 3000 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) [ B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B 1.
Fluids of mechanics
Determine the magnitude(lb) of the vertical component of force at point C if P = 137 lb, x = 14.7 in, y = 8.3 in, and z = 7.5 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use U if upward and D if downward.
In the frame shown below, what is the value of horizontal reaction force component at C? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for left. Horizontal force component at C, Cx = N 2000 N B. 3 m 2 m 2 m 60°
Vector O is the resultant of vector M = 9.9i + 3.8j + -3.5k and an unknown vector N. Vector O is a vector in the positive z-direction only and has twice the magnitude of vector M. What is the magnitude of vector N? Express your answers in two decimal places.
choices are given