In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x10-6 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm (1) A 100mm 300mm 6kN 400mm

In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x10-6 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm (1) A 100mm 300mm 6kN 400mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: T3-at 2.5 in. above the NA (at the top of the web) = ksi T4 at 1.25 in. above the NA = T5 at the NA…

A: The dimension are The shear force is

Q: Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A…

Q: For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal…

Q: A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free…

Q: The stress-strain diagram for a steel alloy having an original diameter of 0.80 in and a gage length…

A: Given data Original diameter = 0.8 in Gage length = 10 in Find the load at yielding point.

Q: An open cylindrical tank E mm in diameter and made of F mm thick plate is subjected to an internal…

A: According to the given information we have a diameter of the cylinder is 6 mm. the thickness of the…

Q: (1) Given: b₁ B P=28 kN Square Bars b₁ = 57mm Q = 9 kN C b₂ = 19mm (3) Q R = 38kN b3 b3 ↑ D = 38mm R…

A: given; p=28KNQ=9KNR=38KNb1=57mmb2=19mmb3=38mmaxial stress in bar 2 (σ2)=?

Q: 8 kN C 8 kN В L 45° 45° 60° A E D

Q: In the following Figure using given material properties. a) Determine the internal forces and…

Q: 3. Three bars each made of different materials are connected together and placed between two walls…

Q: as -ja-A Find the approximate prime plane in dogreos for the state of st given in the figure. 45 MPa…

Q: n the mechanism shown below, the distributed load W is 300 N/m and the angle 0 is 55 knowing that…

Q: Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by…

Q: 4- Determine the stress when Temperature change from 20 C° to 60 C° . steel aluminum 20 kN 200 mm…

Q: A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter…

Q: A rigid horizontal bar ABC is supported by three vertical rods as shown. The stress free before the…

A: Given dataChange in temperature, ∆T=110°FApplied Load, P=45 kNFor Rod 1E1=105 GPa , α1=22×10-6/°C,…

Q: A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length…

Q: QUESTION 13 The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2…

Q: 30 -1.5m A D 80KN 5m 80KN 1.5m 40μN

Q: A rectangular plate (0 =20") is formed by welding two triangular plates shown in figure. The plate…

Q: (1) Given: P=28 kN b₁ B Square Bars b₁ = 57 mm P Q =9 kN (3) Q R = 38 kN b₂ = 19mm b3 ↑ D = 38mm R…

Q: See the set of bars for made of a material that has a yield strength of 350 MPa, determine the…

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: Figure 3 below shows a vertical rod under its own weight. Find the displacement at A and stress…

Q: (1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm VIO (3) Q R = 38kN b3 b3 ↑…

Q: I NEED THE ANSWER ASAP. I WILL GIVE YOU A TIP ON PAYPAL IF YOU HELP ME SUBMIT AS EARLY AS POSSIBLE.…

A: Longitudinal Stress

Q: A bar made of a metal alloy has the dimensions shown in Figure. If an axial force of P=10xb kN is…

A: P=10×b KNP=10×5=50 KNL=3×aL=3×2=6 mt=10×a=10×2=20 mmw=20×a=20×2=40 mmE= 210 Gpa μ=.32

Q: Determine the shear stress of the cylinder pivot pin (φ25mm). The clamping force of the pliers is…

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

A: Given: The structure is made up of stock (same stock for A-B-C and B-D). 5 mm thick. b mm wide.…

Q: V = (Ax?) i +(B/y) j What are the dimensions of A and B? What are the units of A and B?

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

A: Area = A = 20 X 30 = 600 mm2 Force normal to area Pn = 400 cos (30) Pn = 346.41 KN

Q: E= 103 GPa E = 75 GPa E= 190 GPa 0.8 mm 150 mm 100 mm 300 mm Bronze Al Steel

A: Stress produces in the material due to changes in temperature is known as thermal stress. Condition…

Q: Determine the values of the stress in the steel bar as shown in the figure below when the…

A: Find the stress and force in the bar.

Q: 3. If P= 100KN, Compute the total deformation. 1,2 m 201 60 CM 7P $=2ch $=6m E = 200 GPa = 100 GPO…

A: To find : The total deformation. Given that : The force is P=100 kN1000 N1 kN=10×104 N. The diameter…

Q: 4. V = (Ax?) i +(B/y) j What are the dimensions of A and B? What are the units of A and B? 5. Nine…

A: Given:

Q: Find the Normal Stress at points A, B, and C

A: To Find the Normal Stress at points A, B, and C

Q: THE MAGNITUDE OF THE LOAD ( F= kN) WILL BE THE SUMMATION OF ALL THE NUMBERS IN YOUR STUDENT NUMBER.…

A: In this question, the first step is to find the components of the applied on the point of…

Q: Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5 mm. You…

A: Step 1: Step 2: Step 3: Step 4:

Q: 3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

Q: A round Steel rod of 50 mm diameter is bent into an arc of radius 10m. What is the maximum stress in…

A: Any action that can change the state of motion is called force, Force is described by its magnitude,…

Question

In the following structure if the temperature increases by 20 °C, determine the normal stress in Links
(1) and (2).
E (GPa)
A (mm2)
a (1/°C)
11.9x10-6
Link 1
200
310
Link 2
70
620
22.5x106
500mm
350mm
B
to
A
100mm
300mm
(2)
6kN
400mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Do not answer in image format. Answer completely.
The principal stresses shown below are calculated at two different cross sections of a brittle machine part. Determine if the cross section A or B is safer (Sy = 50 MPa, Sut = 100 MPa, and Suc = 200 MPa). 0,50 MPa + 0₂ = -20 MPa A 0₂=-20 MPa 0₁ = 50 MPa a, 20 MPa - ₂ =-120 MPa B 0-120 MPa a₁ = 20 MPa
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget to show me your step
Please answer with full steps and drawings please
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
Rank the normal stress in each section of the bar. Rank the values of normal stress from largest (largest tensile stress) to smallest (largest compressive stress). Use AB for segment AB, BC for segment BC, and CD for segment CD.
1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in cach material given that P = 10 kN? Bronze Aluminmım Steel A=400 mm2 2P A=600 mm A= 300 mm 3P 4P P m 5m- -4m-
Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure.
10 ft 7.5 in 400 lb 400 lb 30 3.5 in The wood grain the tension member above are oriented approximately 30 degree to horizontal. Which of the following is closest to the magnitude of shear stress acting parallel to the grain? O11.4 psi O3.81 psi O 15.2 psi 6.60 psl
In mechanical resistance
Determine the normal stress in each segment of the steel rod shown in the figure. E-200 GPa. A = 600 mm² A B 300 KN + 0.3 m A 200 mm² 200 KN 0.3 m 0.4m D 100 kN