In the figure, two blocks are connected over a pulley. The mass of block A is 11.0 kg and the coefficient of kinetic friction between A and the incline is 0.150. Angle e of the incline is 36.0°. Block A slides down the incline at constant speed. What is the mass of block B? Frictionless, massless pulley-

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: Successive approximation ADC explian

A:

Q: Write the mathematical form of Newton's second law of motion.

A: Newton’s second law of motion states that the resultant of actual force is always equal to effect or…

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: hi still waiting on the last part of the question..

A: Application of ballast tanks in aerospace

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: Answer in number 7 and 8.

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: F L 30 F L A E L L L L В D M

A: Drawing the free body diagram of the given system:-

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: Where did the 0.10472 rad/s come from?

A:

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: Determine ly and ky.

A:

Q: 5. (a) (i) A crane hook with a mass of 80 kg exerts a vertical force F downward at A (see Figure…

A:

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Draw the Venn Diagram and write your answer in set roster notation. 5 pts A={1,2,3,4} B ={1,3,5,7}…

A: Venn diagrams are used to establish relation between things or a finite group of things with the…

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: Represent the following as a number between 0.1 and 1000 using an appropriate prefix:568(10^5)mm

A: Given: The given number is N=568×105 mm. The conversion factor to convert the given unit in the…

Q: name these lines

A: The names of the given lines is given below.

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: At a certain instant, the particle of mass m has the position and velocity shown in the figure, and…

A:

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.