In the figure, rigid bar ABC is supported by axial member (1), which has a cross-sectional area of 400 mm², an elastic modulus of E = 70 GPa, and a coefficient of thermal expansion of a = 22.5 x 10-6 /°C. The temperature rises 56°C causing deformation at pt. B. Determine the deflection at pt. C? 1.75 m D (1) B 3.75 m 1.25 m C

In the figure, rigid bar ABC is supported by axial member (1), which has a cross-sectional area of 400 mm², an elastic modulus of E = 70 GPa, and a coefficient of thermal expansion of a = 22.5 x 10-6 /°C. The temperature rises 56°C causing deformation at pt. B. Determine the deflection at pt. C? 1.75 m D (1) B 3.75 m 1.25 m C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An element in uniaxial stress is subjected to a tensile stress of 49 MPa in the x – direction.Determine the stresses acting on an element oriented at an angle of – 27 oC from the x – axis(clockwise direction)
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
Both wires have a cross sectional area of 17 mm? and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible. 900 mm 450 mm C D 500 mm 1250 mm P=1500 N 1650 mm
4. A uniform bar with an area of o.25 in- is pulled between two points. The tensile force at a temperature of 21.11°C is 1200 lb. What will be the stress at -17.78°C? At what temperature will the stress be zero? Assume a = 6.5 × 106 in/(in-°F) and E = 29 × 10ʻ psi. %3D %3D
Problem No. 4: The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250 mm?. If the temperature is increased by 80°C, determine the force P that will cause the bar at C to be stress-free. Use E=200 GPa and a=12 x 10-6/ °C. 3 m 0.8 m. 0.6 m Ba Ce
Problem # 8: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson's ratio to be 0.33. Determine the value of loads P and its axial deformation. d = 12 mm P L 1.20 m P
(Problems No. 1- 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the normal stress at the y-axis 60 MPa 20 MPа 90 MPа O a. 75.60 MPa O b. -24.60 MPa 69.8 MPa O d. -39.8MPA
9. The initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and BD. Undeformed Deformed A B D 2.0 mm 2.015 mm C 1.995 mm
A tied column 350 mm x 600 mm in cross section is reinforced with 6-28 mm Ø bars arranged as shown in the figure. It is assumed that the column section has a strain on its compression edge equal to 0.003 and has a tensile strain of +0.002 on its outer edge. f = 27.6 MPa. fy = 414.6 MPa. 350 mm 62.5 Tension Bars 600 mm 475 6-28 mm Ø 62.5 Compression Bars - Determine the total compressive force of the steel reinforcement considering that its compressive stress is reduced by 0.85 f' to account for the holes in the concrete. 2 Determine the nominal axial load that causes this strain distribution in the column section. 3 Determine the nominal moment that causes this strain distribution in the mn section.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
Three forces, each of magnitude P = 4 KN, are applied to the structure shown. Determine the cross- sectional area of the uniform portion of rod BE for which the normal stress in that portion is 100Mpa. 0.100 m D |B 0.150 m 0.300 m 0.250 m
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad