In the figure below two pipes containing the same fluid of density r = 990 kg/m3 are connected using a u-tube manometer. What is the pressure difference between the two pipes if the manometer contains fluid of relative density 13.6? d density P روليك و كيمياء تربة Fluid density P ha=1.5 m h, = 1.5m hb = 0.7 5m hb=0.75 m h = 0.5m h=0.5 m Manom ctr ic flu id density Pa 13.6 P man

In the figure below two pipes containing the same fluid of density r = 990 kg/m3 are connected using a u-tube manometer. What is the pressure difference between the two pipes if the manometer contains fluid of relative density 13.6? d density P روليك و كيمياء تربة Fluid density P ha=1.5 m h, = 1.5m hb = 0.7 5m hb=0.75 m h = 0.5m h=0.5 m Manom ctr ic flu id density Pa 13.6 P man

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure difference between two points as measured with a manometer is given as ?2 − ?1 = ??ℎ The following figure shows a single U-tube manometer for measuring pressure difference between points “A” and “B”. By determining the pressure at point “a” through the left leg and then through the right leg, show that the difference in pressure between point “A” ?? and “B” ?? is approximately given by ?? − ?? ≅ ?(ℎ2 − ℎ1)(??2?)
In the inclined manometer shown in the figure below, the reservoir is large. Its surface may be assumed to remain at a fixed elevation. A is connected to a gas pipeline and the deflection noted on the inclined glass tube is 100 mm. Assuming q = 30° and the manometric fluid as oil with specific gravity of 0.86, the pressure at A is A 100 mm Ꮎ B
A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
Similitude Water flows through a 5 inch diameter pipe at 10 ft/s. If a test is performed using mercury moving at 4 ft/s, what diameter pipe (in inches) would be needed to maintain the same dynamic characteristics? Both fluids are at standard temperature and pressure. Hint: What dimensionless number do we use all the time for pipes?
An orifice meter is a device used to determine the flow velocity and flow rate in a pipe. The meter is connected to a U-tube manometer shown in Figure 2(a). The meter is connected to a U-tube manometer shown in Figure 2(b). Derive the equation for the flow rate, Q in the horizontal pipe.
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3. pls answer asap thank you
1. The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. The tank is A deep and is contaminated with B of water. The specific volume of gasoline is 0.00147076 m /kg and that of air is 0.0008313 m³/kg. Unit weight of water is 9790 N/m3 a. Determine the gage reading when the tank is full of gasoline b. How many cm of air remains at the top when the gage indicates full if the tank is A deep and is contaminated with B of water. c. Determine the pressure at the interface of the gasoline and water when the gage indicates full A = First name in inches Vent B = A/10 in inches Air h A Gasoline Pgage Water B
Q2: Compute the value of (H) in centimeters such that the pressure at B is 90% of the pressure at point A. If the pressure at A is 79.4 kPa, S.G (oil)=0.89, S.G (mercury)=13.6. SAE 30 oil Gage B Mercury- 6 сm H Water flow 11 cm 4 cm
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
1) A manometer is attached to two pipes as shown. If knowing mercury SG is 13.6, sea water SG is 1.035, and fresh water p is 1,000 kg/m³, determine the pressure difference between two pipelines at the centers. Fresh Water h. -60 cm Air hair -70 cm hea <- 40 cm Mercury Sea Water hi -10 cm
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).
In a manometer shown, the fluid from A to B is mercury (sp. gr. = 13.6) and fromB to C, the fluid is oil (sp. gr. = 0.80). At what height, h, of oil will give a pressureof 452 grams/cm2at C. Use density of water of 1.0 grams per cu.cm.