In the figure below, find the value of uniform load w (kN/m) that can be applied on the composite beam if the maximum stresses in steel and timber are 48MPa and 3.2MPA, respectively. Est=195GPA,Etimber=13GPA 120mm W Steel 10mm Timber 300mm 2m 4m 2m 250mm Steel 10mm 120mm

In the figure below, find the value of uniform load w (kN/m) that can be applied on the composite beam if the maximum stresses in steel and timber are 48MPa and 3.2MPA, respectively. Est=195GPA,Etimber=13GPA 120mm W Steel 10mm Timber 300mm 2m 4m 2m 250mm Steel 10mm 120mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A prestressed beam is given in the figure below. X Aps = 696 mm2 H = 540 mm B = 350 mm y = 90 mm L =…

A: Area of steel, Aps=861 mm2 H=560 mm B=350 mm y=110 mm Initial pre-stress, fps=1208 MPa

Q: The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa.…

A: Calculate the axial force in each of the segments of the given bar. Then using the algebraic sum of…

Q: For the following composite beam which is built up out of two wooden beams and three steel plates,…

A: Given- For Wood- E = 15 GPa σmax = 7.5 MPa For Steel- E = 200 GPa σmax = 150 MPa To Find- Moment…

Q: A composite beam is constructed using a steel plate (15 mm x 170 mm) with two wood beams (75 mm x…

Q: A timber column, 8 in. by 8 in. in cross section, is reinforced on all four sides by steel plates,…

Q: A timber beam shown in the figure is made up of Kamagong (50% stress grade). Use LRFD. All the given…

Q: The properties of the reinforced concrete beam are b = 314 mm, d = 467 mm, Ast = 1047 mm2, and Est /…

A: Given data b = 314 mm d = 467 mm Ast = 1047 mm2 fc = 17.9 MPa fs = 103.2 MPa n = 9 Using…

Q: Which among the formulas below can be used to compute the combined stress at the bottom fiber of a…

A: ASKED: To compute the formula for combined stress at the bottom fiber of a beam subjected to axial…

Q: When solving the problems for Section 1.6, assume that the material behaves linearly elastically.…

A: Given data in question Diameter Elasticity modulus Poissons ratio To find out Largest force P

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 40…

A: In composite beam, bending strain diagram is linear and strain compatibility conditions is used to…

Q: A compressive force P is applied to a 75mm by 100mm piece of wood. The wood grain makes a 20- degree…

A: To determine the largest axial load P that can be safely applied to the wooden column. Given,…

Q: Calculate the design moment strength of a reinforced concrete beam 230 mm x 460 mm if at failure the…

A: Reinforced concrete is a composite material in which the poor tensile strength and ductility of…

Q: b) The rectangular section shown below is subjected to a moment of M=257kN.m. Assume a cracked…

Q: thick. It supports an axial load of 1,000 kN. E for timber is 10 GPa and for steel, E = 200G 10 200…

A: Because of strain compatibility δsteel =δtimber σsteel LEsteel =σtimber LEtimber…

Q: A rectangular steel block is 4 inches long in the x direction, 2.5 inches long in the y direction,…

A: Given:- Dimensions of rectangular steel block are Length in x-direction = 4 inches Length in…

Q: A composite beam is under external loads as shown below. Draw the internal shear force and bending…

A: Length of span= 3.6 mUdl= 40 kN/mPoint load = 75 kN

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

Q: • width of beam, b = 350 mm • thickness of beam, t = 450 mm • f'c = 20.7 MPa • fy = 415 MPa • steel…

A: Answer We need to find the ultimate moment on the beam. Ultimate Moment(Mu) will be equal to maximum…

Q: The joists of a floor in a warehouse are to be selected using square timber beams made of oak. The…

A: the maximum shear stress : The most concentrated shear force is the one with the highest shear…

Q: Consider a composite bar that is firmly attached to unyielding supports. Compute the stress in each…

Q: A piece is subjected to compression traction loads in two dimensions with ox 90 Kg/cm2 and oy= -120…

A: Stress on vertical plane, σx =90 Kgcm2Stress on horizontal plane, σy =-120 Kgcm2

Q: A pre tensioned concrete beam 100 mm wide and 300 mm deep, initial force of 150 kN at an…

A: Given 100 mm wide 300 mm deep Initial force P =150 kN at eccentricity e = 50 mm Moment of inertia…

Q: The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P =…

Q: A rectangular beam A = 1,520 mm² fu= 27 MPa (cylinder strength) f₁ = 3.5 MPa (modulus of rupture)…

A: As = 1520mm2 fcu = 27MPa (cylinder strength) fy = 400MPa fr = 3.5MPa (modulus of rupture)…

Q: A high-strength steel band saw, 26 mm wide, runs over pulleys 1200 mm in diameter. What minimum…

Q: Q4: A rectangular beam has the dimensions shown in figure below. Tensile strength in bending…

A: Given: Modulus of rupture, fcr = 3.5 MPa M = 63 kNm fc = 25 MPa fy = 414 MPa Es = 200000 MPa Ec =…

Q: For the composite beam shown in the figure below, determine the maximum stresses in steel and…

A: Solution: Considering the diagram: The stresses in aluminium and steel is calculated using bending…

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

A: As per company policy, we are supposed to answer the first three sub-divisions. Repost the question…

Q: Problem 6.108 The wood used for the T-beam has an allowable tensile and compressive stress of…

A: Given :

Q: tensile steel ratio

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 50…

Q: There is reinforced concrete beam section given as a representative in the figure. It will be…

Q: g) the maximum bending stress in timber. Enter your answer in MPa to 2 decimal places.

Q: Homework 3: Q1/ The beam shown in figure below consists from steel and aluminum, find the maximum…

A: Trusses are the most useful structure to carry the different types of load conditions under pressure…

Q: A wood beam carries the loading shown in the figure, calculat mm from the top of the of the beam on…

Q: The ratio of strain at the centroidal level of compression steel to strain at the centroidal level…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: A composite beam cross section is made up of two rectangular strips. Each of (100x50) mm placed and…

Q: determine the modular ratio n. Enter your answer to 4 decimal places.

Q: The cross-section of the reinforced concrete beam having an effective depth of 500 mm is shown in…

Q: determine the safe resisting moment of the beam in KN.M.

Q: Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total…

A: The given figure is shown below:

Q: A simply supported post-tension beam as shown in Figure (1), span length is 14m, carries a uniformly…

A: To address the problem, we need to calculate the initial pre-stress force \( P_i \) and its location…

Concept explainers

Applications of Concrete Framing Systems

A concrete frame is a structure formed by the interconnection of beams and columns to form a structural network. In simple terms, it is the basic skeletal structure of a building or any construction. The concrete framing structure is built on a concrete foundation that forms the base of the entire structure. The concrete frame system is built to support floors, roofs, walls, beams, rafters, joists, etc.

Question

In the figure below, find the value of uniform load w (kN/m) that can be applied on the
composite beam if the maximum stresses in steel and timber are 48MPa and 3.2MPA,
respectively. Est=195GPa,Etimber=13GPA
120mm
W
Steel
10mm
Timber
300mm
2m
4m
2m
250mm
Steel
10mm
120mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Applications of Concrete Framing Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
#4 will upvote anyone who will answer
Solution w/FBD
A composite T-beam is built up out of plywood and steel angle sections. The steel angle sections have 100mm long sides and are 10mm thick. What is the maximum allowable distributed load (w) if we do not want the materials to go beyond their allowable stresses. Given: For plywood: E = 15 GPa, σmax = 8 MPa For steel: E = 200 GPa, σmax = 150 MPa
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axia! loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Steel 2 ft Bronze 4 ft A (in.²) E (psi) o, (psi) Aluminum 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 4P Aluminum 0.50 10 x 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
4. Steel and aluminum plates are used to reinforced 100 x 175 mm timber beam. The three materials are fastened firmly as shown so that there will be no relative movement between them. Given the following material properties, determine the safe resisting moment of the beam in KN.M. Allowable bending stress, Fb Modulus of Elasticity, E Steel = 130MPA Steel = 210MPA Aluminum = 90 MPa Aluminum = 80 MPa Wood = 20 MPa Wood = 15 MPa 30 mm CTEEL WOOD ww.skl A LUMINUM 140 mm
A rectangular steel bar with given dimensions is subjected to a axial compression. What is the critical buckling load? width, b = 42 mm thick, t = 60 mm L = 3.25 E = 180 Gpa
The wood beam has an allowable shear stress of Tallow = 4 MPa. (Figure 1) Figure Part A 50 mm 50 mm 200 mm —+ ➜ 50 mm ↓ 100 mm 100 mm 1 of 1 Determine the maximum shear force V that can be applied to the cross section. Express your answer to three significant figures and include the appropriate units.
The beam shown in the figure below is subjected to a factored shear force of 200 kN and shear resisting capacity of concrete for the given amount of reinforcement provided is 0.62 N/mm2. The shear stress for which beam should be designed is N/mm?. 1200 120 380 3 - 220 40 250 (All dimensions in mm)
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Calculate the design moment strength of a reinforced concrete beam 200 mm x 460 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 22 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.