In the analysis conducted with flame AAS, standard solutions of the X-type are analyzed individually and the absorbance values ​​obtained are plotted against concentration (ppm). It was seen that the slope of the calibration line obtained was 0.0925. The standard deviation of the absorbance values ​​obtained by reading the blank 10 times under the same conditions was calculated as 0.00183 ppm. According to this; For the X-type calculate the following: a) LOD b) LOQ c) Sensitivity

Q: Classify the following substituents according to whether they are electron donors or electron…

A: Inductive effect is defined as the permanent displacement of electron density towards more…

Q: You have measured the blank for a determination of arsenic in food samples by hydride-generation…

A: Given, Sr. No. (N) 1 2 3 4 5 6 7 8 9 10 Blank values(ppb) 0.23 0.14 0.16 0.28 0.18 0.09 0.10…

Q: An HPLC setup has an injection volume of 0.353 mL and a detector volume of 0.300 mL. The baseline…

A:

Q: The calibration curve for FD&C yellow #5 dye has a slope of 35188 L/mol with an intercept of 0.007.…

A: Given: Calibration curve for FD&C yellow #5 dye has Slope = 35188 L/mol Intercept = 0.007…

Q: B. The copper concentration in a contaminated salt sample was determined by flame atomic absorption…

A: #8: Flame atomic absorption spectroscopy is used to find the copper concentration in the…

Q: An unknown sample of Yellow 6 solution has the absorbance equal to 0.96. The slope of the Beer's law…

A: The capacity of any sample to absorb the light of a particular wavelength is expressed by its…

Q: A spectrophotometer method for the quantitative analysis of Pb2+ in blood uses Cu2+ as an internal…

A: given : SASIS = 0.8320.351= 2.37 CA = concentration of analyte = 1.75 CIS = concentration of…

Q: (c). What is the dynamic range of the method? Hint: it is NOT the entire concentration range. (d). A…

A: Atomic absorption spectroscopy is a quantitative spectroscopic method to determine the concentration…

Q: A 0.05 mM solution of DCPIP was placed in a 1 cm spectrophotometer cuvette and a beam of light at…

A: We know that absorbance = log (I0/I) = e*c*l

Q: Derive an expression relating absorbance to the concentrations of standard and unknown ( c subscript…

A: Volume of the solution = 10 mLVolume and absorbance data of an aqueous solution is given.

Q: A calibration graph was established with a slope of 0.186 and an intercept of -0.026. The absorbance…

A: Solution:- Data provided => Slope = 0.186, Intercept = -0.026 And Absorbance = 0.357 Lambert…

Q: A researcher is interested in determining the detection and quantitation limits of a method for the…

A: The explanation is given below-

Q: 2. A linear standard curve of KMnO4 is prepared from a set of standard solutions by plotting…

A: The objective of this question is to plot a standard curve of KMnO4 using the given data. This curve…

Q: If the initial amount of Fe(NO3)3 transferred to the cuvette is 0.029 mol, and the absorbance…

A: Given Data :Initial Amount of Fe(NO3)3 = 0.029 molEquilibrium amount of FeSCN2+ = 0.019 molTotal…

Q: What is the Molar Absorption Coefficient for Fe(SCN)2+ (M/cm) if the path length of vial is 2.24cm…

A: In the given question we have to calculate the molar absorption coefficient of Fe(SCN)2+ by the…

Q: Low concentrations of methylmercury near the detection limit gave the dimensionless instrument…

A:

Q: Deduce the analytical technique used and calculate the concentration of wastewater analysed which…

A: A calibration curve and follow up questions which are to be accomplished.

Q: The detecton limits reported for Al with ICP-AES and GF-AAS are 2 ppb and 5 picograms, respectivly.…

A: Given:Al with ICP-AES = 2 ppb = 2 µg/L = 2×10-6 g/L.Mass of Al with GF-AAS = 5 picogram = 5×10-12…

Q: Lithium in a sample is determined by flame emission spectrometry, using a standard additions…

A: If 10 microlitres of 0.010M of lithium nitrate on addition gives 14.6 units, then the sample without…