Answered: In the absence of collar friction, the…

Engineering

Mechanical Engineering

In the absence of collar friction, the power screw described in the previous two problems is self-locking.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

Clear selection Determine the number of pin joints 7. Which of the following has multiple degrees of freedom?
Find out degree of freedom ?number of link ,joint, must be indicted like as link symbol L and Joint symbol j.
Clearly explain the methodology involved in determining torque, power, and efficiency of power screws. Draw diagrams wherever necessary. Formulae derivation is not necessary, but include the formulas. Explain self-locking case.
= It is required to design a split muff coupling to transmit 60 kW power at 140 rpm. The shafts, key 420 N/mm²). The yield strength in and clamping bolts are made of plain carbon steel (σyt compression is 160% of the tensile yield strength. The factor of safety for shafts, key and bolts is 5. The number of clamping bolts is 8. The coefficient of friction between sleeve halves and the shaft is 0.3. (i) Calculate the diameter of the shaft. (ii) Specify the length and outer diameter of the sleeve halves. (iii) Find out the diameter of clamping bolts. (iv) Specify the size of key and check the dimensions for shear and compression criteria
RB&W¹1 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4 diameters, 1/2 turn for bolt grips 4-8 diameters, and 2/3 turn for grips of 8-12 diameters. These recommendations are for structural steel fabrication (permanent joints), producing preloads of 100 percent of proof strength and beyond. Machinery fabricators with fatigue loadings and possible joint disassembly have much smaller turns-of-nut. The RB&W recommendation enters the nonlinear plastic deformation zone. The figure shows a cross section of a grade 25 cast-iron pressure vessel, with a torque factor K of 0.09. Use Eq. (8-27) to estimate the torque necessary to establish the desired preload given that preload F; = 14.4 kip, bolt stiffness kb = 5.21 x 106 lbf/in, number of threads N = 11, and material stiffness km = 8.95 × 106 lbf/in. in-11 UNCX 2+ in grade 5 finished hex head bolt in No. 25 CI Determine the torque necessary to establish the desired preload and the turn of the nut in…
RB&W11 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4 diameters, 1/2 turn for bolt grips 4-8 diameters, and 2/3 turn for grips of 8-12 diameters. These recommendations are for structural steel fabrication (permanent joints), producing preloads of 100 percent of proof strength and beyond. Machinery fabricators with fatigue loadings and possible joint disassembly have much smaller turns-of-nut. The RB&W recommendation enters the nonlinear plastic deformation zone. The figure shows a cross section of a grade 25 cast-iron pressure vessel, with a torque factor K of 0.09. Use Eq. (8-27) to estimate the torque necessary to establish the desired preload given that preload F;= 14.4 kip, bolt stiffness kb = 5.21 x 106 lbf/in, number of threads N=11, and material stiffness km = 8.95 × 106 lbf/in. in-11 UNCX 2 in grade 5 finished hex head bolt in in 162 No. 25 CI Determine the torque necessary to establish the desired preload and the turn of the nut in…
A. PROBLEM ON TOPIC "KEYS AND COUPLINGS": A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... is also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required bif a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on kev, then select your answer. Length Based on shear length Based on compression:…
Deeith a bolt spacing and gage distance of 0.6br is critical for prying action if the holt tension force is 85% of its capacity. Use LRFD.
Given written specifications, develop the note for a threaded fastener. With the following specifications, develop the note for this threaded fastener. The threaded fastener has: • a major diameter of 3/4 inch, • a pitch length of 0.050 inches, • a unified coarse thread form, • which has a class of fit of 2, • it is an internal thread, and • has a length of thread engagement of 2 1/2 inches.
The output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A is fixed and bed B is free-formed. Which of the following is true for the inner and Outer Ring of the bearing in bearing B?Please select one: a. Because the FG force acts on the shaft, there are no forces coming to the bracelets.b. the inner ring has a point, and the Outer Ring has an environmental load.c. Environmental load affects the outer ring.d. environmental load acts on the inner ring and point load acts on the outer ring.e. both environmental and point load affect the inner ring.
TRUE OR FALSE. ANSWER ALL QUESTIONS OTHERWISE DONT ATTEMPT IT STRICTLY. I WILL REPORT YOU IF U ATTEMPT WITHOUT ANSWERING ALL QUESTIONS.
forms! Explain Self-locking and over-hauling conditions for a power screw using sketch and its formula. Give example where Self-locking and over-hauling conditions are desired. A doubles