In order to increase the strength of the pressure vessel, filament winding of the same material is wrapped around the circumference of the vessel as shown. If the pretension in the filament is T and the vessel is subjected toan internal pressure p, determine the hoop stresses in the filament and in the wall of the vessel. Use the free-body diagram shown, and assume the filament winding has a thickness t and width w for a corresponding length L of the vessel.

Q: A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the…

A:

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

A:

Q: respectively. The tank has an inner diameter of 4 m. The thickness of the cylindrical are made from…

A: A scalar quantity in when when an amount of force act on the object in a cross section area, that is…

Q: in the figure. Also, determine the factor of safety for the tank based on Von-Misses and Tresca…

A:

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A:

Q: 2. Consider the Flamant solution - a line load on the edge of a half space. The valid stress…

A: according to a given question

Q: 15. A bar of 12 mm diameter gets stretched by 3 mm under a steady load of 8 kN. What stress would be…

A: Since the question containes multiple questions. I am answering only one question (15) only. So,…

Q: The concrete post (E = 3.6 x 10° psi anda = 5.5 x 10-6/F) is reinforced with six steel bars, each of…

A:

Q: A pressurized steel tank has inner radius r = 0.5 m and wall thickness t = 20 mm. The steel has…

A: Given data: Before proceeding with the solution check whether it is a thin or thick pressure…

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. (Figure 1) Figure…

A: According to the given datad=12 int=0.25 inP=280 psiWe need to findLongitudinal and hoop stress when…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: At a party, a parent is blowing up a birthday balloon until its diameter is n = 3.4 times the…

A: Introduction In this problem, we will compute the normal stress in the balloon after inflation, for…

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: Q2 / The 60° strain rosette are mounted on articular cartilage element. Figure Q2 shows the readings…

A: Consider the diagram shown below for the strain rosette. The general equation for the strain in a…

Q: The steel pipe in (Figure 1) has an inner diameter of 4.57 in. and an outer diameter of 4.82 in.…

A: To find: The principal stresses at point A. Given: The outer diameter of the pipe is do=4.82 in. The…

Q: The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two…

A:

Q: A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow…

A:

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

A:

Q: The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.