in a sprinkler irrigation system, the following information is given: the length of the sprinkler pipe is 360m, the pipe is made from Aluminum C=100), where C is the Hazen -Williams roughness coefficient, sprinklers are spaced at 12 m*18 m (L*S), gross depth of irrigation (GDI) is 150 mm, the number of working hours at one location is 11 .hour, pipe slope is 0% Find Average pressure head -1 Pipe diameter -2

in a sprinkler irrigation system, the following information is given: the length of the sprinkler pipe is 360m, the pipe is made from Aluminum C=100), where C is the Hazen -Williams roughness coefficient, sprinklers are spaced at 12 m18 m (LS), gross depth of irrigation (GDI) is 150 mm, the number of working hours at one location is 11 .hour, pipe slope is 0% Find Average pressure head -1 Pipe diameter -2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular duct must connect with a circular duct. The rectangular ductmeasures 6 inches by 7 inches. The circular duct has a diameter of 7 inches.Which duct has the smaller cross-sectional area?
Final answer is 219.5 Kp Please show steps Thank you
Energy Loss in Bends and Fittings a) What is the difference between major loss and minor losses in a pipe network? Give at least three examples of minor losses? b) The following information has been collected in the lab during "Head Loss in Bends and Fittings" experiment: Manometer readings for sections before and after a bend: h₁=326 mm and h₂=253 mm Q=0.28 lit/s Pipe diameter 1.83 cm Calculate the head loss coefficient (K) for this bend. - c) Name the fitting from the lab experiment (excluding the valve) that should have the highest head loss and explain why this is the case?
Make a solution plz
Please use the table to answer the second question
Question: A sewage treatment plant for a town with 120000 population and water average temperature of 20 °C should be designed. You are asked to design a coagulation/rapid mixer and a flocculation tank with horizontal shaft paddle. The jar tests suggest average G-value of 30 (m/s)/m, minimum water residence time of 1500 seconds and GT value from 55000 to 90000. The flocculation tank should include 3 compartments with similar compartments' geometry aspects separated using baffles partitions. The width of each flocculation tank should not exceed 7 meters due to some constraints highlighted by the project's mechanical engineers about the maximum length of each shaft. Determine: 1- The volume and dimension and power requirement of the cylindrical rapid mixer 2- The flocculation tank dimension 3- Required power for each flocculation mixer 4- The paddle wheel dimension 5- Rotational speed of each mixers (Check if the speeds are acceptable) 6- Baffle size and distribution 7- Write about any…
C PART ONLY
Direction: Choose A- When both statements are true; B - When both statements are false; C- When the first statement is true and the second statement is false; D-When the first statement is false and the second statement is true. Da Based on the figure above, First Statement: The aquifer is an unconfined aquifer because of the presence of aquiclude. Second Statement: The direction of groundwater flow is from A to B. B Oc
The figure shown is a frustum of a cone with an orifice in the bottom of 0.20 m². If the water level outside is constant at point 2, how long will it take the level in the cone to drop from point 1 to point 2? Assume C = 1.0. 14.0 m. 10 m water 17 -6.0 m- COMPLETE SOLUTION. NEED ASAP. THANK YOU.
4. The results of the liquid limit tests are given below 23 48.1 No of blows Water Content (%) 53.9 Draw the flow curve and if the plastic limit is 25 and the natural water content is 50 % What is the liquidity index? 1.30 11 15 30 46 53 50.6 46.0 43.3 41.0 А. B. 0.91 C. 1.17 D. 1.25