In a proposed highway undergoing road earthworks, the given roadway cross-section notes are as follows: STA 20 + 100 2.30 -6.45 1.50 0.00 1.00 4.50 STA 20+ 300 2.00 -6.00 1.20 0.00 2.60 6.90 Width of the roadway is to be determined using side slope of xH:1V where x is the unknown horizontal side of the slope. Show and draw plotted points of the cross-section of roadway each station. Calculate the following: 1. Total number of man-days to finish the earthwork job 2. Total cost of machine rentals to finish the earthwork job. In the inventory of available heavy equipment on site are two (2) hydraulic excavators with bucket payload capacity each of 0.76m³ and one (2) hydraulic excavator with bucket payload capacity of 1.15m3 The hourly production of each excavator with 100% efficiency are 149m³ and 196m respectively. Daily machine rental fees for smaller capacity is 1,200 pesos while bigger capacity costs 2,200 pesos. Daily machine operation is limited to 8 hours.

In a proposed highway undergoing road earthworks, the given roadway cross-section notes are as follows: STA 20 + 100 2.30 -6.45 1.50 0.00 1.00 4.50 STA 20+ 300 2.00 -6.00 1.20 0.00 2.60 6.90 Width of the roadway is to be determined using side slope of xH:1V where x is the unknown horizontal side of the slope. Show and draw plotted points of the cross-section of roadway each station. Calculate the following: 1. Total number of man-days to finish the earthwork job 2. Total cost of machine rentals to finish the earthwork job. In the inventory of available heavy equipment on site are two (2) hydraulic excavators with bucket payload capacity each of 0.76m³ and one (2) hydraulic excavator with bucket payload capacity of 1.15m3 The hourly production of each excavator with 100% efficiency are 149m³ and 196m respectively. Daily machine rental fees for smaller capacity is 1,200 pesos while bigger capacity costs 2,200 pesos. Daily machine operation is limited to 8 hours.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The longitudinal section of a runway provides the following data: End-to-end runway (m) 0 to 300 300 to 600 600 to 1100 1100 to 1400 1400 to 1700 Gradient (%) +1.2 - 0.7 +0.6 -0.8 - 1.0 The effective gradient of the runway (in %, round off to two decimal places) is
Homework Q1: A driver of a vehicle traveling at 90 kph up-grade requires 96m to sto after he applied the brakes, less than another driver traveling at the same speed down the ame grade, if the coefficient of longitudinal friction is 0.3. What is the percent grade of thatsection and what is the total stopping sight distance on the down grade? Q2: In the figure shown below, its required to calculate the minimum distane (D) for placing the right turn sign to enable a driver on the major road (A) to turn his vehicl into minor road (B)?
designing a rural highway is required so how many lanes are needed in the peak hour based on the given information:v = 4000 vehicle/ hour (per lane )level terrainPt ( trucks ) = 15%Pr = 3%Fp =1lane width 3.6mlateral clearance 1.8mphf =0.85interchange density = 0.9 interchange/km..no LOS was given and the units (metric)
A railroad curve has D₂ = 3°00', I = 25°00', and PI station = 35+ 45.00 ft. Use the chord definition to calculate the requested values. Part B Calculate the length of the curve, L. Express your answer to two decimal places and include the appropriate units. L = Submit Part C T = Submit Part D 0 E = Value μÀ O Calculate T Express your answer to two decimal places and include the appropriate units. Request Answer 0 μA Value 6 Request Answer HÅ Value wwwww Units Units Calculate E. Express your answer to two decimal places and include the appropriate units. 2 ? Units wwwww ? ?
For a highway curve with Da = 5°00', I = 20°30', and Pl station = 63 +25.53 ft, calculate the requested values to lay out the circular curve at full stations (100 ft). Part A Calculate the radius. Express your answer to two decimal places and include appropriate units. R= Part B μA L = Value Calculate the circular curve length. Express your answer to two decimal places and include appropriate units. μA Units Value ? Units ?
Given highway design parameters below, solve the questions a) through f). A curved section of a 4-lane undivided highway (i.e., 2 lanes rotation) Design speed = 40 mph • Design max superelevation = 8% Lane width = 11 ft • 2.5% normal crown Central angle(l) = 38°, Degree of Curve = 7.82°, and Plsta = 292+52.4 a. Determine PC,ta b. Determine PTsta c. Calculate the length of full superelevation (BFS EFS) ENC: End of Normal Crown; LC: Level Crown; BFS: Begin of Full Superelevation; EFS: End of Full Superelevation
For a highway curve with Da = 5°00', I = 20°30', and Pl station = 63 +25.53 ft, calculate the requested values to lay out the circular curve at full stations (100 ft). Part D Calculate the middle ordinate. Express your answer to two decimal places and include appropriate units. M = Part E LO E= μÃ Value Calculate the external distance. Express your answer to two decimal places and include appropriate units. μA Units Value ? Units ?
While designing a rural road for the Safe Stopping sight Distance (SSD) for the designvehicle with an operating speed of 85 km/h, the design team (comprising Team leader,Design Engineer, Technician, Traffic Engineer, Surveyor and other team members) needsto consider the road segment to be an unsealed up-grade road with longitudinal slope 3%and reaction time is 2.5 s. How much safe stopping sight distance is required for that roadsection?
From the following cross section notes where SSis 1.5H:1V and width of highway is 20.00 meters at every station. Determine the following: 1. Total road volume using end area 2. Total road volume using prismoidal formula 3. Total road volume using prismoidal correction Cross -Section Notes STA 5+100 - 6.2 -6.0 -12.0 -5.3 0.0 -4.0 10.0 -8.8 -X - 4.2 -2.0 8.0 STA 5+160 -5.0 -8.0 -6.5 0.0 -7.6 -X Draw the cross-section of profile of roadway per station.
Thickness of broken centre line markings for a four lane road, is generally kept (A) 10 cm (B) 12 cm (C) 15 cm (D) 18 cm Minimum permissible speed on high speed roads, is decided on the basis of (A) 15 percentile cumulative frequency (B) 20 percentile cumulative frequency (C) 30 percentile cumulative frequency (D) 40 percentile cumulative frequency \ The full width of land acquired before finalizing a highway, alignment is known (A) Width of formation (B) Right of way (C) Carriage way (D) Roadway
Question 2- the corner of a building next to a horizontal curve with a radius 40 m on a rural highway. The inside lane is 3 m wide and the edge of the road shoulder is 2 m from the corner of the building. The shoulder width is 1.2 m. Determine what speed limit should be imposed on this section of the highway. (63+2.53) (36 +847) + (83+3-33)/ (120 +08) Sight Distance (5) 94 100 (100-00)-(63+2.53) (36 +97.47 Highway Centerline- Line of Sight HSO -Centerline of Inside Lane 20 Shoulder Sight Obstruction 550 HS0 =3m+ 2m +12m 35km/ (footoo)-(63+2-53)
هندس ... Calculate the right of way of rural divided four-lane highway has depressed median and it is constructed on embankment. The median width is 4.50 m, embankment height is 5.5m, lane width is 3.75 m, shoulder width is 2.50 m and side slope is 1.25:2.5 (V:H). A- B I EE 00 22 5 Pa 2