Q1: A driver of a vehicle traveling at 90 kph up-grade requires 96m to sto after he apPplied the brakes, less than another driver traveling at the same speed down the ame grade, if the coefficient of longitudinal friction is 0.3. What is the percent grade of thatsection and what is the total stopping sight distance on the down grade?

Q1: A driver of a vehicle traveling at 90 kph up-grade requires 96m to sto after he apPplied the brakes, less than another driver traveling at the same speed down the ame grade, if the coefficient of longitudinal friction is 0.3. What is the percent grade of thatsection and what is the total stopping sight distance on the down grade?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the grades of a symmetric VC that requires a stopping sight distance of 434.3 ft and minimum length of VC 873.9 ft. Determine also the maximum speed limit to be imposed if it is to be by increments of 5 mi/hr and 10 mi/hr. Assume vehicle eye levels of 3.5’ and 2.0’, both situated inside the VC. Use the same deceleration value in the previous problem.
4. A building is located 8.8 m from the centerline of the inside lane of a curved section of highway whose radius is 145 m. the road is level and e is equal to 0.10. Determine the maximum possible posted speed limit (to the nearest 5 km/h) assuming that the coefficients of longitudinal and side friction are equal to 0.35 and 0.13, respectively.
2. Calculate the total stopping sight distance for a wet pavement condition, if the design speed is 100 Km/hr for the following three conditions. a. Road is flat b. The road has a 6% downslope c. The road has a 3% upslope
QUESTION 2 What is the calculated stopping sight distance (ft) for a +6% grade when the design speed is 50 mph, assuming the AASHTO recommended deceleration rate and perception-reaction time.
9) The driver of an automobile moving with the velocity of 90 km/h on a 4% graded descendinghighway section decides to overtake the bus moving with a velocity of 70 km/h despite theapproaching truck with a velocity of 50 km/h on the opposite direction.a) What should be the minimum distance between the automobile and the truck at thebeginning of the overtaking for safe manouevre ?b) If the truck has to stop op the highway, what is the upper and the lower limit of the tractionforce that must be diverted to its wheels in order to restart moving ?Given: di=8+0,2.Vi; pavement sliding coefficient, f=0,40; t = 0,020; the mass of the truck = 12ton, Qm=2/3.Q
A cargo truck of J&T is to driven up a 5% grade at 120kph. The coefficient of road adhesion is 0.9 and its known that the braking efficiency is 85%. Determine the theoretical stopping distance if the driver has a reaction time of 0.7sec and the rolling resistance is 0.0137?
Q. What is the psychological widening of a pavement on the horizontal curve of radius 230m for ruling speed 80 Kmph?
What will be the ruling radius of a horizontal curve on a National Highway for a design vehicle speed of 100 km/h, assuming allowable super elevation to be 7 % and lateral friction as 0.13 ?
Design speed of a six-lane undivided highway is 70 mph. A circular section of the highway has level grade, 10-ft wide lane, and the radius of the highway centerline is 1000 ft. Calculate the minimum side clearance required from the edge of the innermost lane on the highway to provide adequate sight distance for safe travel
QUESTION 4 What is the calculated stopping sight distance (ft) for a -3% grade when the design speed is 55 mph, assuming the AASHTO recommended deceleration rate and perception-reaction time.
How do you prefer a ‘tracked drive’ system than a ‘tired drive’ system for an excavator?
Q5/ A- A highway section. +2%, meet -8% at point with 52.0 m at speed 110 Km/hr. Determine the elevation of the highest point on the pavement surface within this