Step bt step solutionProblem 2: A horizontal curve on a single-lane freeway ramp is 400 ft long, and the design speed of the ramp is 45 mi/h. If the superelevation is 10% and the station of the PC is 18 + 25, determine: A) the curve radius B) the central angle C) the tangent length D) the station of the PI E) the station of the PT F) the stopping sight distance G) the distance that needs to be cleared from the center of the lane to provide adequate stopping sight distance

Step bt step solutionProblem 2: A horizontal curve on a single-lane freeway ramp is 400 ft long, and the design speed of the ramp is 45 mi/h. If the superelevation is 10% and the station of the PC is 18 + 25, determine: A) the curve radius B) the central angle C) the tangent length D) the station of the PI E) the station of the PT F) the stopping sight distance G) the distance that needs to be cleared from the center of the lane to provide adequate stopping sight distance

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rising gradient AB and a falling gradient BC are to be connected by a vertical curve. Based on the data given in Table Q1, design the curve at 20 metres intervals. Table Q1 (Units are in metres) First Grade (± %) Second Grade (+ %) Sighting Distance (SSD) Driver's eye (h₁) Object height (h₂) 4.2 -1.8 145 1.05 0.3 F G RL of highest/lowest pt Chainage of highest/lowest pt| H 39.171 4048.600 K
I need the answer as soon as possible
The question about civil (transportation) engineering. This is my homework,please help me
1. Two vertical parabolic curves have been connected to form a roadway by three gradients: -5.30 %, 4.10 % and -3.70 % respectively. If the length of the second curve is twice as the length of the first curve, compute the following: a. The length of the second curve in ft given that the design speed of the first curve is 80 kph assuming a vertical radial acceleration of 0.3m/s for comfort criterion. b. The length of the second curve in m if the headlight height of the vehicle is 0.73 m above the first curve and the inclined upward angle of the headlight beam relative to the horizontal plane of the vehicle is 1.57'. The design speed for the first curve for this situation is 90 kph. c. The length of the first curve in yard if the total length of the roadway is 745 m given that the second curve has a design speed of 70 kph for passing sight distance with the driver's eye height assumed to be 1.5 mand object height of 0.33 m d. The total length of the roadway in km if a bridge structure…
Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed=60 mph, max superelevation=8% 2) The design/full superelevation, in %, is: O 7.2 O 7.4 O 7.6 O 7.8 O 8.0
Please answer question below and include all steps on how you got the answer
An equal-tangent vertical curve connects a +3.2 % and a -1.1 % grade. The PVI is at station 100+20 and elevation 950 ft and the PVT is at station 105+20. Answer the following 5 questions Question 3 to Question 7. The station of the PVC is at: sta 93+20 sta 95+20 sta 97+20 sta 99+20 sta 105+20
A sag curve connects a -1.5 percent grade with a +2.5 percent grade on a rural arterial highway. The criterion selected for design is the minimum stopping sight distance, and the design speed of the highway is 70 mph. Assume the perception-reaction time of 2.5 seconds and a deceleration rate of 11.2 ft./sec^2. a. Determine the length of the curve. b. Compute the elevation of the curve at PVC and PVT if the grades intersect at station (475 + 00) at an elevation of 300 ft.
A vertical curve is formed on a two lane undivided highway between the tangents of 1 gradient + 1 Assume the height of driver's eye and height of obstruction and 100 50 as 1.4 m and 0.18 m respectively. Determine the length of vertical curve so formed considering stopping sight distance calculated using the following parameters. Design speed of vehicle = 80 kmph Reaction time = 2.5 sec Down gradient = 2.5% Coefficient of longitudinal friction = 0.38
What will be the ruling radius of a horizontal curve on a National Highway for a design vehicle speed of 100 km/h, assuming allowable super elevation to be 7 % and lateral friction as 0.13 ?
You have been tasked as a Highway Engineer to undertake the geometric design of the Block Factory road which is a collector road leading to AIT Seaview Campus in Accra using a design speed of 60km/hr, superelevation of 5% and trailer as design vehicle. Specify the desirable values to be employed for the following design elements: (AP,5)i. Maximum standard gradientii. Minimum vertical curve lengthiii. Minimum horizontal curve radiusiv. Curve widening amountv. Single carriageway width
A 4-lane divided highway has a highway grade of -1.5%. The minor road approach grade is 3.5%. The design speed is 45 mph for the major road and 40 mph for the minor road. Find the left turn departure sight distance for a passenger car turning left from the minor road to the major road, The answer should be in feet.