in a closed system process, 600 Btu of heat is added to the system, and the internal energy of the system increases by 220 btu. calculate the work of the process

Q: A 'long' steel shaft of 10 cm diameter is austenised at 870°C and then quenched in a liquid at 30°C.…

A:

Q: Which of the following whose values are  not depend on the transition of a system from the initial…

A: State functions are those functions whose values are not dependent on the transition path of the…

Q: A heat pump cycle whose coefficient of performance is 2.59 delivers energy by heat transfer to a…

A:

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: Air flows with a velocity of 6 m/s across a 20 cm? plate at 50 kPa and 300 K. An electrical heater…

A:

Q: (b) An electric kettle with a 3kW heater element is used to boil water. The kettle has a stainless…

A: To determine the temperature at the center of the wire (T_max) and the convective heat transfer…

Q: 1000 lb / hr of oil at 100 ° F flows in a pipe having an ID inch. This oil will rise in temperature…

A: The mass flow rate of oil, moil = 1000 lb/h Initial temperature of oil, Toil,i = 100ºF Inside…

Q: A vessel with a paddle agitator and no baffles is used to heat a liquid at 37.8degC in this vessel.…

A: Given Inside diameter of the vessel, Di=1.22 m Diameter of the agitator, Da=0.406 m Speed of the…

Q: In the case of determining heat rates and fluxes, is power required for the system the same as the…

A: Heat rate: Heat rate is defined as amount of heat (energy) per unit time. Unit of energy may be…

Q: A double pipe heat exchanger consists of a 2" Sch 40 steel pipe inside a 3inch Sch 40 steel pipe, 10…

A: It is given that double pipe heat exchanger is used to condense steam in the annulus bu help of…

Q: Calculate the rate of heat transfer for a steam flow rate of 220 Kg/Sec and latent heat of…

A: Given that, The mass flow rate of steam ms = 220 kgs The latent heat of vaporization λs = 25 kJkg It…

Q: The compression ratio of an air-standard dual cycle is 12, and the pressure at the beginning of…

A:

Q: I understand that we have to use this formula Heat current=(k. Area. change in temperature)/length…

A: Firstly, the brass rod one end is in boiling water, which means this rod is hot. While the Copper…

Q: The pipe is 6 m long with an inner radius of 70 mm, an outer radius of 80 mm, and is made of…

A: The rate of heat transfer through the pipe wall is to be calculated.

Q: 5. . . ) In a manufacturing process, a long, coated plastic rod (p = 2200 kg/m³, c = 800 J/kg K, k…

A: The time it take to the surface of the rod to reach 175o C, the temperature above which the special…

Q: Draw only the schematic diagram and T-S diagram.

A:

Q: A piston-cylinder device initially contains gas at 200 kPa. The system showed an expansion due to…

A:

Q: An automobile engine provides 596 Joules of work to push the pistons and generates 2246 Joules of…

A: Given that, Work done on the system W = 596 J Heat generated by the system Q = 2246 J It is required…

Q: Q.2 An Aluminum plate of area 500cm2 is heated up for 5 seconds and its temperature increases from…

A: Area of Aluminium Plate=500cm2=0.05m2 Thickness=2cm=0.02m Mass of Aluminium plate=3.46kg Time up to…

Q: Which of the following is the rate of heat transfer unit 1. Watt 2. Pascal 3. Joule 4. None of these

A: Heat transfer is the transfer of heat due to modes of heat transfer like conduction, convection and…

Q: 7.1 What is condenser ? 7.2 What are the functions of a condenser in a thermal power plant? Give the…

A: A condenser is an essential component in thermal power plants, converting exhaust steam back into…

Q: Q2/ Air at atmospheric pressure and 27 °C is blown across a long 4.0 cm diameter tube at a velocity…

A:

Q: A piston-cylinder assembly has 1 kg of air at 700 kPa and 400C. The piston cross-sectional area is…

A: This problem is based on the concept of ideal gas law. The data given : Initial temperature ,T1 =…

Q: Q2:- If the amount of heat given to a system be 25 joules and the amount of work done by the system…

A: Write the equation for the first law of thermodynamics as follows: ∆U = Q-W     ......1   Given, The…

Q: Initially, a piston device contains 0.55 m³ of saturated water vapor at 300 kPa and at this state,…

A:

Q: (2) Calculate the Fanning Friction Factor (f) using the formula: = 2.5 In Re, +1.75 8

A: Given, Equation for fanning friction factor is 1f = 2.5lnRef8+1.75    .....1   Here, Reynolds…

Q: A chiller cools liquid water for air-conditioning purposes. If 1.5 kg/s water at 20 °C, 100 kPa is…

A: given data,Initital temp, Ti = 200Cfinal temp., Tf = 50CInitial pressure, Pi = 100 kpamass of water…

Q: 1. When a system absorbs heat, a part is stored within the system as the energy of internal motions…

A:

Q: Steam in a heating system flows through a 1-m long tube whose outer diameter is D1 = 3 cm andwhose…

A: Given: diameter D1 = 3 cm = 0.03 m Radius r1 = 1.5 cm = 0.015 m Circular fins (k = 46 W/m. °C) of…

Q: Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C.…

A:

Q: Q3. Air at 1 atm and 300 K is used to cool a l-m-square plate maintained at 500 K. The flow velocity…

A: Given, The wall temperature, Tw = 500 K The temperature of the air, T∞ = 300 K   Write the…

Q: A high temperature furnace heated by burning natural gas has a wall thickness of 10 cm and external…

A: Given that for furnace- Dimension= 50 cm x 40 cm x 70 cm = 0.5 m x 0.4 m x 0.7 m Thickness of wall,…

Q: Determine the LMTD

A:

Q: a cylinder-plunger contains 2.4x10 ^ -2 kg of air that is subjected to a cycle: Process 1-2:…

A: Given Data :  Mass of air in the cylinder (m air )= 2.4 x 10 -2 Kg  Moles of air (nair) =mass of air…