How much work must be input by the paddle wheel below to raise the piston 5 cm. The initial temperature is 100°F.

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: 7. Determine the number of sprinkler heads required to protect an inside process area of 2000 ft².…

A:

Q: 1. Pumps and its types 2. Pipelines 3. Tanks

A:

Q: How we can calculate friction losses due to changes in velocity and direction in side a conduit

A: Friction losses due to changes in velocity and direction in side a conduit can be calculated as

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: Write down the 2 key parameters that affect the friction losses of the fluid flowing through a…

A:

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: a. Define (note: your definition must be based on the closed conduits/pipe flow): 11. Unit weight…

A: We have to define the following unit weight unit gravity yield stress shear rate

Q: " The impeller of a centrifugal water pump runs at a speed of 800 rpm, it has blades widths; b₁-5cm,…

A:

Q: Sketch the principle of a hydraulic press.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: Determine the constant torque that must be applied to a 50.0kg flywheel, with radius of gyration…

A: The value of the torque applied to the flywheel is to be mentioned.

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Determine diameter of galvanized pipe needed to make the water flow along 180m with flow rate 85L/s…

A: Given data: Length of pipe = 180 m Volumetric flow rate = 85 L/s Head loss = 9 m Kinematic viscosity…

Q: 9. A centrifuge with a radius of 76.2 mm rotates at a peripheral velocity of 53.34 m/s. The…

A: Given Data  The radius of the centrifuge (r) = 0.0762 m Peripheral velocity (V) = 53.34 m/s To Find…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: If the entering velocity is 6 m/s, calculate the length of tube and determine whether the process is…

A:

Q: Determine the hydrostatic force acting on the radial gate if the gate is 40 ft. long (normal to the…

A:

Q: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds? When the…

A: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds?= for laminar…

Q: What problem could arise in the turbine given a certain quality at the exit?

A: The problem that can arise in a turbine with certain quality at the exit is to be mentioned.

Q: Discuss about Momentum and heat transfer operation with examples

A: Momentum transfer - In general, transfer of momentum from one molecules to other molecules due to…

Q: Determine the pressure difference between the two pipelines as shown below in the figure. Page=370…

A: Assumption:1) All the liquids are incompressible2) The effect of air column pressure is…

Q: In tillage operations, the typical required draft per unit width of implement for a clay soil is 5…

A: The wdth and draft width are used to obtain the total draft. The width is considered in units of…

Q: The power output of a wind turbine increases with the following EXCEPT:

A: the power output of the turbine increases with the following except. Select suitable currect option

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: Write a report detailing the energy balance in pumps, with illustrations, formulas, and diagrams and…

A: A pump is used to move liquids with the help of the pressure difference between one point and the…

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: Head developed by a centrifugal pump depends on its A speed ⓇB impeller diameter both (a) and (b)…

A: In chemical industries pumps are used to transport chemicals from one place to another place. A…

Q: In a gyratory crusher the size reduction is effected primarily by: 1.impact 2.attrition 3.cutting…

A: This question is based on crushing and grinding operations. We will analyse each option and find the…

Q: Q1) Water is placed in a piston-cylinder device at 0.5 MPa and 95°C. Determine the work does the…

A: Given: Water is placed in a piston-cylinder device at P = 0.5 MPa = 0.5×106 Pa and; temperature T =…

Q: Compare S.I and C.I engines with respect to fuel used

A: CI engine - Compression ignition engine SI engine - spark ignition engine

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…

Q: Paddle agitator

A:

Q: 0.72 g of a fuel containing 80% carbon, when burnt in a bomb calorimeter, increased the temperature…

A:

Q: Temperature measurement is done using a mercury thermometer; which is protected by a thermowell.…

A: The order of mercury thermometer is to be mentioned with detailed analysis.