Problem 2: A metal rod 0.4 m long & 0.04 m in diameter has one end at 373 K & another end at 273 K. Calculate the total amount of heat conducted in 1 minute. (Given K = 385 J / m s °C)

Q: An aluminium pan whose thermal conductivity is 237 W/m/°C has a flat bottom whose diameter is 20 cm…

A:

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: I at 351 v.v42L i) Calculate the temperature distribution at the middle and rate of heat floe at the…

A: Given,

Q: 1-85 A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board.…

A: given = H = 0.4 cm d = 0.6 cm avg heat transfer coefficient = 30 W/m2K air temp Tair = 55^c…

Q: Given: Plate thickness: 30 mm k = 45 W/m°C Uniform volumetric heat generation: q, = 25 MW/m3…

A: i) Let A be the cross-sectional area perpendicular to the direction of heat flow S (W/m3) is the…

Q: Find all letters, answer for a and b are 39.27 W and 93.7 degrees Celcius Heat is conducted through…

A:

Q: Calculate the heat

A:

Q: 2. Heat is transferred steadily in one direction in a composite plane wall that is made of two…

A: The objective of this question is to determine the rate of heat transfer in the system and the…

Q: (3.4) The gas heater shown below in cross-section consists of a square sheet-metal duct insulated on…

A: a) given = Heat transfer fluid data T1 = 500 K T2 = 450 Kh1 = 200 W/m2K f1 = 0.00035 m2K/w Process…

Q: <p A horizontal tube-bundle air-cooled exchanger is used to condense steam at 240 F and has the…

A: Step 1:

Q: <p A horizontal tube-bundle air-cooled exchanger is used to condense steam at 250 F and has the…

A: I'll answer each question step-by-step, using the given information from the image.1. What is the…

Q: In the case of determining heat rates and fluxes, is power required for the system the same as the…

A: Heat rate: Heat rate is defined as amount of heat (energy) per unit time. Unit of energy may be…

Q: The compression ratio of an air-standard dual cycle is 12, and the pressure at the beginning of…

A:

Q: 3. A vertical furnace door, 1 m. in height has a surface temperature of 120°C over which air (30°C)…

A: Given height of the door = 1m surface temperature = 120°C air temperature = 30°C air velocity = 2.5…

Q: The pipe is 6 m long with an inner radius of 70 mm, an outer radius of 80 mm, and is made of…

A: The rate of heat transfer through the pipe wall is to be calculated.

Q: A spherical object at 10 °C was taken into a bath at 60 °C. The core temperature-time values ​​of…

A: Answer: Initial temperature of the spherical object, T0 = 10°C = 283 K Bath temperature, T∞ = 60°C =…

Q: 19.4 The fuel plates in a nuclear reactor are 4 ft long and stacked with a 1/2-in gap between them.…

A:

Q: 5. . . ) In a manufacturing process, a long, coated plastic rod (p = 2200 kg/m³, c = 800 J/kg K, k…

A: The time it take to the surface of the rod to reach 175o C, the temperature above which the special…

Q: Water available at 24 C is heated by a heating element having 30 mm outside diameter and 0.4 m…

A: Cp=4180J/kg.∘C k=0.64W/m∘C density(r)=988kg/m3 μ=0.55×10-3N-S/m2 Ts=80∘C length=0.4m do=30mm=0.03m…

Q: 8. For polytropic process the heat and work can not cross the boundary of the system * False True

A: Given, Concept of Polytropic Process Find,  For polytropic process the heat and work cannot cross…

Q: 16.5 Solve equation (16-19) for the temperature distribution in a plane wall if the internal heat…

A: Detailed answers show blown Explanation:

Q: Air at 2 bar and 40°C is heated as it flows through tube of diameter 30mm at a velocity of 10 m/s.…

A: Given, Pressure P = 2 bar Velocity = 10 m/s

Q: Q2. An annulus consists of the region between two concentric tubes having diameters of 3 cm and 5…

A:

Q: Q5) A cube of aluminum 10 cm on each side is initially at a temperature of 300 °C and is immersed in…

A:

Q: 1. Assume steady-state conditions and a thermal conductivity of k 1.5 W/m-K. a. Determine the…

A: Heat Transfer: It is normally from a high-temperature object to a lower temperature object. This has…

Q: What are the reasons for a tubular heat exchanger's internal leak? Describe the baffle rod's role in…

A: Internal leaks in tubular heat exchangers can occur due to various reasons.(1) Corrosion, erosion,…

Q: Q3) A 2-kW resistance heater wire with thermal conductivity of k 20 W/m - °C, a diameter of D = 5…

A: Given that- Resistance heater wire has total heat generation, Q=2 kW= 2000 W Thermal conductivity,…

Q: Liquid food is heated in a tubular heat exchanger. The inner pipe wall temperature is 110 ° C. The…

A:

Q: A 10 ft x 10 ft square sheet of steel one inch thick is at an initial temperature of 1100°F and is…

A: The thickness Length, Breadth, Time,