In a brick-making machine is found this train of gears. A motor carrying pulley E, which is 8 in. in diameter, drives the machine. The wide-faced roller F, 14 in. in diameter, drives a conveyor belt. If the motor runs at 1500 rpm. what is the speed of the conveyor belt in ft. per minute? (Neglect the thickness of the

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: (B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an…

A:

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a…

A: Given Data:Based on the given problem, the solution is as follows:Convert the motor power from…

Q: 1 to one module.

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: Please answer the attach file

A: The number of teeth of gear 2 is N2=24 teeth. The number of teeth of gear 3 is N3=78 teeth. The…

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: le a reverted train Fig. (1), An arm A Carries two concentric separate wheels B and C a compound…

A:

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

A:

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction.…

A:

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: The spur gearing arrangement  made of two parallel shafts,whose pitch circle diameters of driven and…

A: Gear: The gear is rotating part of the mechanical device. The gears are having the number of teeth…

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: 1. Classification of gears according to the possibility of movement of gears axis of rotation…

A: Introduction: A gear is a spinning circular machine element with cut teeth or inserted teeth that…

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: For the epicyclic gear train shown, wheels B and C are rigidly attached to the input shaft (p) and…

A:

Q: Q(1): For the component epicyclic gear train shown in the figure, the number of teeth of gears (A, B…

A: Given diagram:

Q: Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the…

A: Given Data The number of teeth on pinion is:t1=28 The number of teeth on the gear is:t2=70 The…

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear…

A: Given Data Ts=32 teeth Tr=72 teeth Arm y=20 rpm

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200…

A: For the given epicyclic gear train let C.W. direction be positive and C.C.W. direction be negative.…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring…

A:

Q: An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth…

A:

Q: Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output…

A:

Q: lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle.…

A:

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Q: The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A…

A: Given : The radius is The pressure angle  for the spur gear is The pressure angle of bevel gear at D…

Q: A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. The addendum length…

A: Given Z1 = 30 Z2 = 40 Pressure angle = 25 Length of addendum = 5 mm Module = 5.5 mm N = 1500 rpm To…

Q: Q: The sunwheel D has 20 teeth, the gear is 50 teeth, internal gear C is fixed. The input shaft…

A: Sun wheel Arrangement  Given Data The sun wheel teeth D , ZD=20 The sun wheel teeth C, ZC=50 Input…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.