Question 14In a Brayton cycle, air enters the cycle at 1.01 bar and 307 K. The compressor increases the pressure by a factor of 8 and is polytropic (index of compressionn 1.11). Air flows through the cycle at 7.4 kg/s. Fuel, with a calorific value of 44 MJ/kg is burnt ar a rate of 45 g/s. What is themaximum temperature reached in the cycle? Give your answer to the nearest Kelvin. For air cp -1.005 kJ/kgK and cy-0.718 k/kgK.Quesion 14 of 25

Brayton Cycle P1=1.01 bar T1=307 K ma=7.4 kg/s mf=45 g/s CV = 44 MJ/kg

In a Brayton cycle, air enters the cycle at 1.01 bar and 307 K. The compressor increases the pressure by a factor of 8 and is polytropic (index of compression n-1.11) Air fiows through the cycle at 74kgs Fuel, wth a calorfic value of 44 Mg s bumt at arate of 45 gs What a the maximum temperature reached in the cycle? Give your answver to the nearest Kelvin. For air cp 1.005 gk and 0.718 gk.

In a Brayton cycle, air enters the cycle at 1.01 bar and 307 K. The compressor increases the pressure by a factor of 8 and is polytropic (index of compression n-1.11) Air fiows through the cycle at 74kgs Fuel, wth a calorfic value of 44 Mg s bumt at arate of 45 gs What a the maximum temperature reached in the cycle? Give your answver to the nearest Kelvin. For air cp 1.005 gk and 0.718 gk.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
i need the answer quickly
Q6/ In Diesel engine the air at the beginning the compression stroke the pressure and temperature 100kpa, 4OC respectively. The compression ratio is 16 and cut off ratio is 2.2. Find the maximun pressure and tempe rature. Heat imput, thermal cfficicncy and thc work down?
Do part d and e
Exit temperature?
7 The schematic of a two stage air compressor with an intercooler is shown. 100 kPa, 290 K 1.6 MPa C2 °C. (Assume all process to be The temperature of air after first stage compression is ideal and optimal)
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…
Ao air turbine with one intet and one exit operates at Steady State, and has heat trans fer to the Surroundings at an average 3.0x' 10" J per ka of air flowing. The inlet conditions are 980°K and 400 kPa, and the exit conditions are 670°k and 100 kla. Neglect kinetic and potential energy e ffects and use the ideal gas madel without assumung constant specific heats, to calculate the entropy producHon per mass of air flowing. Pres ent your answer in kJ/ (kgʻk) wsing 5 Signifigant figures. outer surface temperature of 315°k ät the rate of
Problem # m, an aii - water mper misture at 15.85 °C and l01.3 i procensed RO the 15,85 °C new kilo Parcal @ satur ation pressure u 3 50 kilo pascal cooled to the liguid pemoved. no the final and water n procedsed again finally l40 Ki lo Paracal It is rocended press ure is at 15.85°C . Jolve for % humidi typ final gas mi n ture araumphin : Vapor press ure water e IS. 85°C - 1.8 kPa