4n ide al Piesel cy cle with alx as the working fluid has a LompresSA 8atio of 18 and a of 2. At the of compres- sion しut Dff ratie beginning tha

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: what is 6 to 10 po?

A:

Q: where did 144 come from

A:

Q: solution incorrect resolve again

A:

Q: resolve solution

A:

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: can you answer 1B

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Determine Stres

A:

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: D raio s.f.D and B.M.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Create an example of Hooke's Law

A: To create: The example of Hooke's law. Concept used: Hooke's law: Hooke's law states that the…

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.