[3] A transmission line circuit consists of an air transmission line of length 175.75A and characteristic impedanceZ, = 100 2 which is terminated in a load impedance Z, = 50 2 and driven by a voltage source with phasor voltagev, = 5 0° v and internal impedance R, = 502, as shown below:1) Find the input impedance Z, of the transmission line.11) Obtain the phasor voltage and current equations describing the variation with position on the line of thephasor voltage V(2) and phasor current I(2).111) Find the time-average powers incident at, reflected by and absorbed by the load.1v) Modify the circuit using a quarter-wave transformer which would produce impedance matching at theload plane so that the reflection at the load plane is killed.

Solution- l = 175.75λ i) l=175.75λ…

Answered: impe Z,- 100 2 which is terminated in a…

impe Z,- 100 2 which is terminated in a load impedance Z, - 50 2 and driven by a voltage source with phasor v v - 50' v and internal impedance R,- 50, as shown below:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Line Voltages at the terminal Pz:- The of abaancat Y conmected load is----- Each Phase of the load cousist of loL30 S2 Find the active s Reactive and somflex Power fer Phase then Find the total load. Var=12010, Powers for Heree phase
Given at the load: Vioond = 452-25° VRMS, 452-25° VRMS, Iload What are the real and reactive power and power factor at the load? Exclude the units. real power: reactive power: power factor: Iload-10-25 ARMS what type of impedance is seen at the load? R. L. or Ch
Pz:- The of abalanced Y connected load is- Each phase of the load cousist of loL30 s2 Find the Line Voltages at the terminat actives Reachive and somflex Power Per Phase then Find the total Powers For Heree phase load. VAB =10010for 4
A three-phase alternator generating unbalanced voltages is connected to an unbalanced load through a 3-phase transmission line as shown in figure. The neutral of the alternator and the star point of the load are solidly grounded. The phase voltages of the alternator are Ea = 1020º, Eb = 102-90°, Ec = 10/120⁰ E E E The positive sequence component of the load current is (A) 1.3102-107⁰ A (B) 0.3322-120° A (C) 0.9962-120º A (D) 3.5104-81⁰ A +) + j1.002 0000 j1.002 0000 j1.0Ω vovo j1.0Ω 0000 j2.002 voor j3.002 oooo
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THOS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE THE LETTER WITH THE CORRECT ANSWER AND PLEASE PROVIDE YOUR CLEAR SOLUTION! A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
Problem: Given wye connected source: La Ven Van Von 6-1892 A 6-j802 N 6-j8Q2 I₂ Von = 120-120° V = 120 <-240° bn where V = 1200° an a) Find the line-to-line voltage phasors for the wye connected source. b) Find the line current phasors in each of the three phases of the resistive load. c) Find the current flowing in the neutral.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Determine the value of the impedance, Z₁, that causes maximum power transfer in the circuit shown in Figure Qlc. 52 j24n -j12.35n (V₂) j2403 j24n Figure Qle B
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents? Need full working and answer has to be 9.3A Formola for inductance XL= 2×3.142FL FORMOLA FOR CAPACITOR XC= 1/2×3.142×FC