A 15-kv, 35-kVA 076PF laggny 50H2 four Pole y-connected Steaw- turbine genevuty has a Synchronons reactane of 3.5on Per phase. Ihis genevatu is operating in parallel with large power System (Infnite'bus). O Sketch Hhe corespouding Phasor diagrum and calcula te frr the armatune current (assume the fel Currut is unchanged ). O At the alsolute power Possile, how much reactive Pover will this generator be supplymy a Consumng?

A 15-kv, 35-kVA 076PF laggny 50H2 four Pole y-connected Steaw- turbine genevuty has a Synchronons reactane of 3.5on Per phase. Ihis genevatu is operating in parallel with large power System (Infnite'bus). O Sketch Hhe corespouding Phasor diagrum and calcula te frr the armatune current (assume the fel Currut is unchanged ). O At the alsolute power Possile, how much reactive Pover will this generator be supplymy a Consumng?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Find the parameters of this 25kW Generator with Armature current of 30A Go A A reaster alaes Broan, Black, Brn, Gald Ceglea Tolerance) meced shunkkdin 5 sets.Each sets hes pd ech typical B: Sane mitrth A but shined a 2ws and endh set had als of cach shkd
Which type of wind turbine needs yaw control? O a. Savonius wind turbine O b. Darrius wind turbine O c. Giromill wind turbine O d. Horizontal axis wind turbine
Desian aproblem for wye delta transform adions Determinc the eauivalend resistance between the terminals A andA B.
Two impedance, Zi = 0.8+j5.6N and Z2 = 8 – j162, and a single- phase motor are connected in parallel across a 200Vrms, 60Hz supply as shown in figure below. The motor draws a 5 kVA at 0.8 power factor lagging. I3 0.8 S3 = 5KVA At 0.8PF lag 20020°V M j 5.6 j 16 (a) Draw the circuit in Matlab Simulink (b) Find the current in each branch and verify your answers from simulation results (c) Calculate the power factor and verify the answer from current phasor angle. (d) Improve the power factor to 0.95 by connecting capacitive load in parallel. Verify the answer from current phasor angle. u
4
Sum of scattering angles in Laboratory coordinate system is always equal to * O 2n None of them О п/2
This is a comparison between lab and wave , please add confirmation and arrange it more orderly,
a syn A: A sylienfonotus generator of 100 MVA, 22 kV, and 0.25 pu transient reactance supplies a motor of 50 MVA, 22 kV, and 0.2 pu transient reactance. The motor is drawing 40 MW at 0.8 power factor leading and terminal voltage of 21.9 kV. The line connecting them has a reactance of 0.05 pu on a base of 100 MVA. Find the transient currents in the generator, the motor, and the fault when a 3-ph fault occurs at the motor terminals. Take SB = 100 MVA, VB = 22 kV, and use the internal voltages %3D %3D of the machines method.
From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? %3D Np:Ns 6:1 D. Vp 120 Vac 60 Hz Vout R = 200 Q O 20Vrms O 720Vrms O 120Vrms O Ovrms wi m
When the load on a series generator is increased, then the fluxproducedwill increaseindirect proportion. Select one: True False
V1 = 170 V f1 = 100 Hz 1) A single-phase load has an active power of P = 2 kW at V1 V @f1Hz and the power factor is cosφ = 0.75. This motor iscompensated to cosφ = 0.85 using a parallel capacitor Find the reactive power difference between compensated and uncompensated status (which will give the capacitor power) and calculate XC and C using the power difference value?