Answered: A long shunt d.c. compound generator…

A long shunt d.c. compound generator delivers 110 kW at 220 V. If r = 0.01 ohm, r = 0.002 ohm, and shunt field has a resistance of 110 ohms, calculate the value of the induced e.m.f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.55 V respectively. The form factor of this circuit is a. 3.67 b. 0.55 c. 1.35 d. 1.83
The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID
Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm resistor is in series with a 40-?F capacitor across a constant potential source of 180 volts. Determine frequency that will give current of 3.13 amp. A. 250 Hz C. 160 Hz B. 200 Hz D. 140 Hz
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Please solving them all. Determine the total current, diodes' voltage and current using a. second approximation b. third approximation All diodes are silicon with bulk resistance of 1.2k ohms. Round off answers in five decimal places.
Q2 (a) Figure Q2(a) shows a clipper circuit made with a gemanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10N and RL=1 kN. (i) Sketch the full cycle of input voltage, Vin(t) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. R. Vin Si Ge R VOUT Vpc Figure Q2(a)
Shown below is a diode circuit. If the input signal Vs = 42 Vp-p and the DC voltage Vdc = 8 V, what is the output voltage (in volts) of the circuit during the positive alteration? No need to show your solution. Just write your numeric answer on the space provided. Round off your answer to 2 decimal places. C1 Si D1 Vo Vs 1.0kn Vdc
Calculete I1, I2 and I3 currents for an ideal opamp in the circuit given in the figure.
The D diode used in the diode circuit shown in the figure is a silicon diode. a. Plot the output voltage of the circuit. b. Describe the working principle for each phase in detail R1 10 kN V out +12 V D R2 100 N Vin-15 sin(wt) R3 220 N
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.
(01) AC Diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
Diodes Are Connected In Series To Share A Total... 21 Question • Two diodes are connected in series to share a total reverse voltage of VD=D 5 KV. Reverse leakage currents of the diodes are ID1=30 mA and Ip2=35 mA. - Find Vp1 and Vp2 for R,=R2=100 k2 - Find R, and R2 for VD1=VD2 R1 VD1 Hint: Is=L,+IRj= I,2+IR2 VD R2 VD2