If we want to make a coil consisting of an aluminum wire of length (100 m), so that it carries a current of (5 A), when the potential difference between its ends is (220 V), what is the value of: 1. Wire resistance? 2. Wire cross-sectional area? 3. The lost power in the wire when the current flows in it? Note that the resistivity of Aluminum is (2.8 x 10-8 Qm).

If we want to make a coil consisting of an aluminum wire of length (100 m), so that it carries a current of (5 A), when the potential difference between its ends is (220 V), what is the value of: 1. Wire resistance? 2. Wire cross-sectional area? 3. The lost power in the wire when the current flows in it? Note that the resistivity of Aluminum is (2.8 x 10-8 Qm).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A wire 50 m in length and 2 mm² in cross section has a resistance of 0.56 2. A 100-m length of wire of the same material has a resistance of 2 N at the same temperature. Find the diameter of this wire.
What is a dielectric material? Give two examples.
Calculate the resistance per unit length of this wire.
Difficult problem that I need some help on please
mp?attempt=2176198&cmid%3D1088508page%3D6 Question 7 Not yet anwend Marked out of 10.00 Hlag question The line shown in the figure has a linear charge distribution of 101 nC/em. If R=8 cm, find the Electric Potential at the point indicated by the dot. Scan clearly your detailed answers and upload it in question 8. R. 2R V=224016.68 V V=134410.01 V V=448033.36 V V=672050.04 v
Discussion Q1\ What is the meaning of resistance, and why it occurs? Q2\ For a copper wire with length (30 m), diameter (1.38 mm), and resistivity (1.72 x 10 2.m), find its resistance at dc circuit? Q31 Why all metals are PTC resistance, while semiconductors are NTC resistance? Q4\ Give four nonlinear resistances with their practical application? Q51 Why is it necessary to connect another resistor before the NTC? Q6\ Did Ohm law's valid with AC circuits, and how? Q71 What is meaning of short and open circuit? Explain with applying Ohm's law to find voltage and current for each one?
Fundamentals of Electric Circuits.
Construct and evaluate a graph to represent the recurrence of discharges in dielectric materials before the breakdown occurs. The graph should consist the voltage across the dielectric, voltage across the void and current impulses.
The working coil of a 0-400 V moving - iron volmeter requires 300 ampereturns to give full - scale deflection.The added resistance is to be three times the coil resistance.Find the diameter of the wire for the coil if the wire be of copper having a resistivity of 1.7 x 10°n cm; the mean length of one turn = 13.5 cm.
Electronics Physics -HW2 Q1. In a P-type germanium, ni = 2×10" electrons/m and the density of boron 4x1023 atoms/m'. The electrons and holes mobility are (0.4 and 0.2 m2/ V. s) respectively. What is its conductivity before and after addition of boron atoms? Note: For after addition of boron atoms you need to compare the actual and approximate conductivity ملاحظة: بعد اضافة ذرات البورون يكون حساب التوصيليه بالاستخدام التقريب وبدون استخدام التقريب والمقارنة بين النتانج
A copper conductor has its specific resistance of 1.96 x 10^-6 ohms-m at 0 degree Celsius and a resistance temperature coefficient of 1/254.5 per degree Celsius at 35 degrees Celsius. Find the (a) the specific resistance and (b) the resistance – temperature coefficient at 90 degrees Celsius.
A 2-wire d.c. ring distributor is 300 m long and is fed at 24Q V at point A. At point B, 150 m from A, a load of 120 A is takeh and at C, 100 m in the opposite direction, a load of80 A is taken. If the resistance per 100 m of single conductor is 0-03 Q, find :(i) current in each section of distributor(ii) voltage at points B and C * 150 m 20 A 240 V 100 m 200 80 A OAA480A, 40,120, VB=200V, VC= 300 IA-86.67, 33.33, 113.33, VB=232.2 N, VC=233.2 V Do one of the above answer