A 2-wire d.c. ring distributor is300 m long and is fed at 24Q Vat point A. At point B, 150 mfrom A, a load of 120 A is takehand at C, 100 m in theopposite direction, a load of80A is taken. If the resistance per100 m of single conductor is0-03 Q, find :(i) current in eachsection of distributor(ii)voltage at points B and C *150 m20 A240 V100 m20080 AOAA480A, 40,120, VB=200V, VC= 300IA-86.67, 33.33, 113.33, VB=232.2N, VC=233.2 VDo one of the above answer

Answered: Image /qna-images/answer/f8c236ae-aedc-46a6-8e61-ba61dc6ec9d5.jpg

300 m long and is fed at 240av at point A. At point B, 150 m from A, a load of 120 A is takeh and at C, 100m in the opposite direction, a load of80 A is taken. If the resistance per 100 m of single conductor is O-03 Q, find :(i) current in each section of distributor(ii) voltage at points B and C * 150 m A 240 V 100 m 200 80 OAAF80A, 40,120, VB=200V, VC= 300 IA 86.67, 33.33, 113.33, VB=232.2 N, VC=233.2 V

300 m long and is fed at 240av at point A. At point B, 150 m from A, a load of 120 A is takeh and at C, 100m in the opposite direction, a load of80 A is taken. If the resistance per 100 m of single conductor is O-03 Q, find :(i) current in each section of distributor(ii) voltage at points B and C * 150 m A 240 V 100 m 200 80 OAAF80A, 40,120, VB=200V, VC= 300 IA 86.67, 33.33, 113.33, VB=232.2 N, VC=233.2 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 13.7- 0-13.7 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D. ст R 38.74 O 19.38 O 24.57 O 30.23 leeee
The voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 2V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm2 ?
20.Show complete solution. Need exact answer.
Choose the best
Power engineering book Mehta
briefly explain what are the other typical applications can be used below mentioned T1.2 Transformers.?
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
conductor radius is 0.75cm
14. The maximum flux of a 50H2 transformer is 0.001Wb. If the primary is wound Vwith 1080 turns, find the applied primary voltage and then calculate the number of turns required for a 15V secondary. Ans: N2=67
Assume 120Vrms is applied to the transformer primary (from P1 to P2). What is the expected secondary voltage measured from S1 to S2? 4:1 Np = 320 Ns = 80 S2 P20 80 Vrms 15 Vrms 30 Vrms 60 Vrms
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes. 110 Vrms 00000 lllll Rsurge www 10 Ω C 100 μF ww RL 3.3 ΚΩ
A certain laminated core has a permeability of 2,500. The length is 5.5 cm and the cross section is 2.1 sq. cm. What is its reluctance? Draw the diagram for the question