Two coils wound on a common core have L1=0.2 H, L2=0.5 H, and M=0.1 H. The currents are i1=exp(−1000t) A and i2=2 exp(−1000t) A. Both of the currents enter dotted terminals. Find expressions for the voltages across the coils.

Two coils wound on a common core have L1=0.2 H, L2=0.5 H, and M=0.1 H. The currents are i1=exp(−1000t) A and i2=2 exp(−1000t) A. Both of the currents enter dotted terminals. Find expressions for the voltages across the coils.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The…

Q: A three-winding transformer is connected to an AC voltage source as shown in the figure. The number…

A: Given- 3 winding transformer, Number of turns- N1=100,N2=50,N3=50, Currents in secondary side- 2∠30o…

Q: 3. A coil consist area ot 0.8 mm? The mean 2.000 turns of copper wire hav ing length par sectional…

Q: The flux linking to 200 turns coil changes from 2 mWb to 5 mWb in 1ms to 3 ms. Determine the induced…

Q: 10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A.…

A: First Calculate the resistance of winding at 15°C: R15=2505R15=50 Ω Now Calculate the resistance of…

Q: 11. There is 900 mA of current through a wire with 40 turns. What is the reluctance of the circuit…

Q: In induction type energy meter, load current 2 proportional to supply voltage V, produces an…

A: Flux and current are in phase

Q: Figure Q1 shows a transformer core that has the primary winding (Np) of 500 second winding (N,) of…

A: Introduction: A transformer is a device that steps up or steps down the level of voltage without…

Q: A two-legged core is shown in figure below. The winding on the left leg of the core (N) has 800…

A: We have given the following problem A two legged core is shown below the winding on the left leg of…

Q: In a certain cast-steel core series magnetic circuit with a 400 turns, 170 At/m, mean length of 0.16…

A: Given, Number of turns, N= 400 turns Magnetic Field intensity, H= 170 AT/m Mean length, L= 0.16 m…

Q: A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of…

A: As given in figure, there are three regions first: top and bottom region l1 =2102+20+52 =55 cm…

Q: use kirchhoffs Junction rule and loop rule to solve for currents I1 , I2 and I3..

Q: Question: 01 A three-legged circular core is shown in figure below. The winding on the left leg of…

A: To determine the total area of the three-legged circular core shown in figure. Now, the Area of leg…

Q: 4. By applying Kirchhoff's rules find currents on every part of the circuit. All devices are ideal.…

A: The circuit diagram,

Q: A toroidal coil, with a circular cross-sectional area of 0.2m2. The coil inductance is 0.28H. The…

A: Given: A=0.2 m2L=0.28 HN=500 turnsψ=498

Q: A two-legged core is shown in figure below. The winding on the left leg of the core (N,) has 600…

A: Given that, N1=600 N2=200 i1=0.5 A i2=1 A μ=1000 We have to find total flux

Q: A 10, 120 V, 60 Hz supply is connected to the coil The coil has 200 turns. The parameters of the…

A: Given values are - E=120Vf=60HzAreaa=20cm2N=200

Q: An air core toroidal coil has 120 turns, the length is 12 cm and 12 sq. cm in area What is the…

Q: A potential difference of 250V is applied to a field winding at 15 C and the current 5A. What will…

Q: toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound…

A: We know direct formula for flux in Toroid due to current . From that formula we will find out…

Q: A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of…

A: The number of turns on the primary side, The number of turns on the secondary side, The voltage…

Q: Ip Ep=40 V f = 60 Hz N₂ = 20- N₁ = 120 Find the maximum flux m om = Find the magnitude of the…

A: In this question, we need to determine the magnitude of the induced secondary voltage Es , maximum…

Q: 5-5.When one coil of a magnetically coupled pair has a current 5.0 A the resulting fluxes ?11and ?12…

Q: The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the core…

A: eddy current loss is given as Pe= k f2Bm2 t2

Q: What do you call a closed conducting path? A Node B Short circuit Loop Junction

Q: A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of…

Q: 2. AC-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the…

A: reluctance = Lμ0μrA flux in the core = MMFReluctance

Q: A two-legged core is shown in the figure. The winding on the left leg (N1) has 600 turns, and the…

A: Flux produced by coil,ϕ=NIRwhere, R=reluctanceR=lμoμrAand,l=length of the coreA=cross-section area…

Q: winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC.…

A: The solution can be achieved as follows.

Q: In the given circuit, if number of turns of coil is 125 and current is 2A, relative permeability of…

Q: ) A ferromagnetic is shown in figure Q3(b). Find the value of the current that will produce a flux…

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The coil of a generator has an…

A: In this question we will find temperature of coil with given resistance value...

Q: 5. An iron core 0.4m long and 5 cm2. In cross section, is wound with 300 turns. When current of 0.5…

A: We need to find out inductance of given coil

Q: 7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with…

A: In this question, We need to determine the rate of current change and power delivered by the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. A coil consist area ot 0.8 mm? The mean 2.000 turns of copper wire haU ing length par copper is 0.02 MICD ohm -m. Find' the resistance absor bed by the coil when connected acoss lov de rupply. sectional a crass - turn is 0o cm and the rerictivity the coil and . power
A toroidal coil, with a circular cross-sectional area of 0.2m2. The coil inductance is 0.28H. The coil has 500 turns. How much current should flow in the coil to get a flux linkage of 498? a. 498.000 A b. 140.000 A c. 1778.571 A d. 249000.000 A e. 889285.714 A
Find out the equivalent inductance for the combination when 2 inductances L1 and L2 are connected in parallel such that their fluxes oppose each other Determine the efficiency of the transformer and find out the value of load at which efficiency will be maximum 3
Answer the question quecly please High voltage
A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. -10 cm- - 20 cm- 15 cm 400 turns 15 cm 15 cm Core depth 5 cm
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
It's urgent please solve asap
There is 50 mA of current through a coil with 250 turns. The flux is 150 µWb. What is the mmf? What is the reluctance of the circuit? A. Fm = 1.25 At - R=4.3x10-3 At/Wb B. Fm = 2.25 At - R=8.3x10-3 At/Wb C. Fm = 1.25 At - R=8.3x10-3 At/Wb D. Fm = 1.25 At - R=8.3x10-2 At/Wb
10. A potential difference of 250 V is applied to a field winding at 15-C and the current is 5 A. What will be the temperature of the winding when current has fallen to 3.91 A applied voltage being constant. Assume temperature coefficient at 15'C is equal to 1/254.5 per °C
7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with a 30-ohm resistor and to a 120-volt d-c source. A switch across the series resistor is then closed, and the circuit is assumed to be in a steady-state condition. At the instant the switch is opened, what will be the rate of current change and the power delivered by the magnetic field.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The coil of a generator has an equivalent resistance of 1.5 ohms at 20 °C. After being used for several hours, the resistance is found to be 1.75 ohms. Determine the temperature of the coils at this time. The temperature coefficient of resistance at 0 °C of the coil is 0.004 OC-1.
Ip Ep=40 V f = 60 Hz N₂= 20- N₁ = 120 Find the maximum flux om om = Find the magnitude of the induced secondary voltage Es Es = units + Is Es units If the coefficient of coupling (k)= 0.75, determine the magnitude of the induced secondary voltage Es Esk=0.75 = units