If the beam will be subjected to a shear force of V=190 kN, determine the shear stress at point H, located at yu = 100 mm above the z centroidal axis.

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: 1/2x10ft

A: We are given: 1/2×10 ft   The given expression is equivalent to computing half the length of 10 f.

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: Sketch SFD and BMD in terms of w and P

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: 1. GIVEN: REQOIREO: yo l0". 7,9 to locete the centreid t 6"

A: To find centroid

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: Determine the centroid of the / ?figure presented in below 1.8 1n 1m1 2m 3m 2 2m 1m 0.5m X >X

A:

Q: Assignment 2.: A line CD, 60mm long, is perpendicular to VP and parallel to HP. It is 20 mm above…

A:

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: What is (-3,0) scale to 1/3

A: Given: coordinates (-3,0) scale = 1/3 To find convert the coordinates to the given scale.

Q: 1⁄6 yard +3⁄8 yard

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: Q1: determaine the coordinates of the centeroid of the shaded area 20 40 50 20 40 30 140

A: The polar coordinate system is a method to calculate points in the system location by proper…

Q: Explain any fiften (15) AUTOCAD commands used in drawing

A: Autocad is a computer based drawing software which is in the field of civil engineering to prepare…

Q: 5 ft 8 ft 2 ft A -3 ft- XB 3 5 4 30 lb B P

A:

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: +y") dx ly

A:

Q: نقطتان )2( Shows polygon with the followng :Find the area (x,y) 2 1.8 1.6- 1.4- 1.2 0.8 0.6- 0.4…

A: answer is option a.)   Matlab command window picture is attached below

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: Fullform of CASBEE

A: CASBEE has been designed to both enhance the quality of people's lives and to reduce the life-cycle…

Q: The column section shown above is reinforced with equal number of 20 mm bars с 1. on each face.…

A: Answer  1) Calculation of neutral axis 'c' We know that at balanced condition strain at extreme…

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: Y

A:

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.

Q: * .I don't like this," said Ali“ Correct Incorrect

A: The correct punctuation marks for this be like this "I don't like this," said Ali.

Q: A Derive the equation for the unit influence line for the reaction at the support B in the…

A: By Muller Breslau method, remove Reaction at support B and place a Load of P as shown in figure. By…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.