+y") dx ly

Q: A9 m. cantilever retaining wall is subjected to active pressure increasing from B kN/m at the top…

A: Given: A cantilever wall with trapezoidal loading on it  X =256, B =5 Required: Maximum shear…

Q: The support at B can be assumed to be a roller. L. What is the reaction at A? (kN) 2. What is the…

A:

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The…

A: The values given in the question are as follows: Span of the beam(L)=4 m or 4000 mm A36 steel grade…

Q: A steel tape is 30.0m long under a pull of (6.0+y) kg when supported throughout. It has a…

A: Correction for pull is:Cp=Po-PsLAEPo=applied pull=12.18 kgPs=standard pull=6.18…

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

A:

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D…

A: Given that:                           Surface roughness, ∈=0.00020 ftDischarge, Q=12.5 cfsDiameter…

Q: 3 m 3 m 3 m E C 12 3 13 50 N D pur answer

A: Yes,  The figure is in equilibrium

Q: Q- A 2500 m long line lying at an elevation of 400 m measures 12cm on a vertical photograph. The…

A: Given data- A 2500 m long line measures 12cm on a vertical photograph. Elevation h = 400 m, Focal…

Q: A grit chamber of rectangular cross-section is to be designed to remove particles with diameter of…

A: Given data- Diameter of particles d=0.25 mmG=2.70settling velocity Vs=2.5 cm/swidth of chamber…

Q: E = 29x 1.' ksi Í 6odiut

A: 1. Determine the fixed end moments FEM for span with udl=wl212FEM for span with point load at centre…

Q: Item 1: Calculate the magnitude of the reactions at the supports.

A: Q##Calculation the magnitude of the reaction at supports using equilibrium ##

Q: What height of oil column will cause the pressure of 5xy kN/m2? What is the equivalent height of…

A:

Q: 1. Y 3" r= 3" 4" 1" 2"

A:

Q: Points 1 2 3 4 5 6 B.S a d I.S b e f F.S c g H.I ارتفاع الجهاز 31.46 31.46 31.46 30.2 30.2 30.2 R.L…

A: Given values: Points B.S I.S F.S H.I R.L 1 a     31.46 29.3 2   b   31.46 28.9 3 d   c…

Q: Situation 2: Given the closed traverse running anti-clockwise tabulated below, determine the missing…

A: Given  X=6, Y=8

Q: Given the closed traverse shown below, determine the missing data. LINE Length (m) Azimuth from…

A: To determine the missing lengths of lines DE and EA.  Given, LINE Length (m) Azimuth from North…

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: P2.10. Refer to Figure P2.9 for the floor plan. Calculate the tributary areas for (a) floor beam B3,…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Given the closed traverse running anti-clockwise tabulated below, determine the missing data.

A:

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: The member is loaded with load P as shown. a) Find the stress at points A,B,C and D b) the points…

A: Question is based on the section subjected to the point load. Magnitude of load and dimension of…

Q: Y

A:

Q: x2 xedy + () +1 dx ||

A:

Q: Find R2

A: For solving reaction we apply equilibrium condition . Equilibrium condition help in findind out the…

Q: Determine the location of the shear centre O of the thin-walled member of uniform thickness having…

A: Given data:

Q: Question 1: Draw Shear Force and Bending Moment Diagram R kN 10 kN/m 8 m 2 m RA Re R = Last two…

A:

Q: dy x3+y3 dx x²y+xy2

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.