75mm Y 25 mm 150 mm 25 mm 25 mm 125 mm

Q: Angular dimensions measure the angle between. two arc O two objects O two circle O Two point O two…

A: Answer - Option e Two lines Angular dimensions measure the angle between two non parallel lines or…

Q: Q2- Find the centroid for the shaded area shown in the figure. (All dimensions in mm) 20 40 20 50 XA

A: Various shape property:

Q: For the following 'shapes', compute the shearing stress at the horizontal neutral axis. Shear force…

A: Given shearing force=104 kN It is asked to compute shearing stress at neutral axis.

Q: 1) Compute the centroid y bar with respect to its base.

A:

Q: Select the lightest W310 that can resist the given loads as shown in the figure. Use the table…

A:

Q: LICATE THE CENTROID 50mm -Somm 150 mm 150 56 mm 400mm

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 69 49 49…

A: A composite section is given as followsy-coordinate of centroid =?

Q: Determine the coordinates of centroid for the given figure shown. 80 mm 50 mm Y 50 mm 150 mm X

A:

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: A 8 = 10+C (degrees) В C…

A:

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: QUESTION 1 rom the figure below, locate the cat id fx and y axes as shown. Y y2 y1 x1 x2 y1 y2 y3 x1…

A:

Q: 38 13 Ф25 12 L 16 16 16 Ф25 56 76 Ф 50 64 7.28 i ,16 25 75

A: Answer :- 1. Top view of section:

Q: rom the x direction, provide the front view, top view, and left-side view using the meter line.…

A: The Isometric Front View, side view, and Top view of above drawing is given Below:

Q: Problem 19-24: A B 30⁰ Determine the maximum force P that can be applied without moving the two Y-kg…

A: only Y = 37 kg is used  and acceleration due to gravity g = 9.81 m/s2 is used

Q: POL -R7.SX0.SX3X2+ 98.5X0.5 K3X2 + AE 86 889 X 1.\/8Y S4s -6.708 X1.118X S4s t 220,2SKI.118XST +…

A:

Q: Looking at the x direction, provide the front view, top view, and left-side view

A:

Q: Problem 9-12: y-axis 90 mm 100+ V (mm) 60 mm x-axis

A: Given Data:X=137, Y=37, A=6, B=8, C=1 The solution to the above given questions are as under-

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. -32 107…

A: The given figure is shown below:

Q: 15mm

A: From a given figure it is required to calculate the centroidal distance from from x and y axis.

Q: Determine the coordinates of the centroid of the shaded area. 10 30 y 1 Answers: x = MI y = i 20 10…

A:

Q: This type of unit is used by metric users where one decimal unit can be equal to 1 millimeter, 1…

A: A system of measurements is called the metric system. It is employed in calculations and research…

Q: W = X N 1m 1ms=0.4 Determine the normal force between the crate and the surface Determine the force…

A:

Q: Looking at the x direction, provide the front view, top view, and right-side view using the meter…

A:

Q: Describe the mechanical cone penetrometer.

A: The cone penetrometer or cone penetration tests (CPT) are performed to obtain the side friction, the…

Q: Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: Instructions :  To draw orthographic projections using third angle projection method, take the view…

Q: want that drawing on AutoCAD step by step picture in a hurry

A: (1) Draw below drawings in top view page using the given co-ordinates (2) Move to isometric page…

Q: Centroid and Moment of Inertia For the following 'shapes', determine the following: (a) Area, A (b)…

A: here for triangular portion suffix 1 is used for rectangular portion suffix 2 is used  for square…

Q: What is the least count of a dial gauge? a. 0.01 m b. 0.1 m C. 0.01 mm d. 1 mm Check

A:

Q: Locate the centroid C(x,y) of the plane area shown below. Arrange your calculations in a tabular…

A: ###Locate the centroid of the plan area and make calculation in tabular format ####Centroid C

Q: Problem 13-14: XN H4,-0.3 Determine the normal force between the crate and the surface Determine the…

A:

Q: origin: center of quarter circle R2 calculate: total area (mm2) centroid along x axis…

A:

Q: Target Range (R) [m] σG A. P P, = (4 t)² R4 where: Pr = power received from the radar in units of…

A:

Q: Determine the second moment of area of the shaded portion about the reference axis Y-Y shown in the…

A:

Q: - 4- पिक (17 b=260m- de-Sm h= 300m = 204N/m to 2onm M= <40kN b f=30kW

A: Given. Udl =20kn/m bending moment 40knm Point load 30kn Draw sfd bmd

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Graph I would like you to please write a drawing clearly so that I can transfer it to graph paper

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.