Answered: If ox = 20 ksi, oy = -30 ksi and Txy =…

Engineering

Mechanical Engineering

If ox = 20 ksi, oy = -30 ksi and Txy = 0 ksi, determine the von Mises stress. a. 61.2 43.6 b. 52.9 33.8 C. d.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: QJThe state of plane stress at a point is represented by the stress element below: A. Draw the…

A: Given Data: σx=70 Mpaσy=65 Mpaτxy=35 Mpa

Q: Calculate and draw the Shear Stress distribution across the depth of the T section shown below, if…

A: Given data: Shearing Force F is 900 kN

Q: 21. If 6, = 30 ksi, o, = 10 ksi, and t,y = 20 ksi, what is the maximum normal stress, in ksi, for…

Q: A 5-mm thick plate of steel is formed into the cross section shown in Fig. P8.13. Locate the shear…

A: The Center of the shear is defined as the place on the section of the beam where the load is…

Q: 12 Problem 02.086.a - Hooke's Law for shearing stress and strain . Determine the change in volume of…

Q: PROBLEM 1.26 For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in…

Q: The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A…

Q: Determine the maximum shearing stress is T=40 kN-m. TABLE 3.1. Coefficients for Rectangular Bars in…

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A: Option d is correct.

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: Question 3 Based on the diagram below a) Find the internal forces of A, B & C. 950 тm 045 тm Ø30mm F…

A: First we need to calculate the reaction from the wall by balancing all the forces. Sum of all the…

Q: Determine the minor principal stress and position of the principal plane when a block is subjected…

Q: H.W.8: Calculate the stresses, if the strains displayed on the lement have been applied. Use all…

A: To obtain the required stresses, we must first determine the principal strains in the element using…

Q: Knowing that the allowable normal stress for the steel used is 174 MPa, determine the section…

Q: Determine the principal planes and the principal stresses for the state of plane stre of stress…

Q: Part 3 * Incorrect. Use the normal stress transformation equation, Equation on = 0x cos²0 + oysin²0…

Q: 1+154 mm 2-234 mm 3+114 mm B-15mm 28 kN |Yo

A: Given that, P=2.8 kNd=15 mm,b1=154 mm,b2=234 mm,b3=114 mm, For the given beam system the force…

Q: 34. Degree of bending moment equations * for both segments AB and BC. a. 3rd degree and 3rd degree O…

Q: If o = 50 ksi, Oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

Q: PROBLEM 1.25 For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in…

Q: The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A…

A: To Find:The normal stress in the direction of the x′-axis.The shear stress in the y′-direction for…

Q: A state of stress at a point A is given by ox = 210 MPa, oy = -140 MPa, and txy = 95 MPa. Which of…

A: The correct answer is option e) 234.071 Mpa

Q: Determire the internal shear force at section 0.5 m from point B to the right in the rigid body…

Q: Question 1: For the given state of stress, by using formula determine; Principal Plane - Principal…

Q: B. Two springs were attached in a series as shown. The maximum Shearing stress of the spring is…

A: Given data: τ=200 MPaG=80 GPa Need to determine the maximum allowable load and total elongation.

Q: Required information Consider the given state of stress. Take X-15 MPa and Y=60 MPa. + + 25 MPa +…

A: The value are

Q: Determine the largest shear force V that the member can sustain if the allowable shear stress is…

Q: Problem 07.018 - Determine stresses parallel and perpendicular to the grain of a wooden element. The…

A: Given: σx = P = - 3.5 MPa σy = - 1.8 MPa τxy = 0 θ=- 15° ( negative due to sign convention )…

Q: Betermine the maxtnum stress In the section A-A as shown - Fig. 7.1. Also mark the reglon In secllon…

Q: Suppose that σx = 42 MPa A) Determine the maximum in-plane shear stress. B) Determine the average…

A: The value of The value of the shear stress, (A) Determine the maximum in-plane shear stress.(B)…

Q: Determine the maximum absolute shear stress for the state of stress at a point shown. a. b. 0 50.0…

Q: Question 1: For the given state of stress, by using formula determine; 25 MPa - Principal Plane…

Q: 1000 Ib The cross-sectional area of each member of the truss is 25 in?. Calculate 1000 lb the…

A: given data; ⇒lets take reaction force at A=RA⇒lets take reaction force at E=RE⇒lets take tension…

Q: The principal stress element is shown. If o₁ = 32 MPa and o₂ = -15 MPa, determine the von Mises…

Q: Four bolts used to lap joint two steel plates together. Tensile force on the plates is 66.7 kN.…

A: Given data: F=66.7 kNn=4τAllow=68.9 MPa Need to determine the diameter of the bolt.

Q: Required information Consider the given state of stress. Take Y=4 ksi. 10 ksi Determine the normal…

Q: If o, = 30 ksi, ơy = 20 ksi, and Txy = 10 ksi, what is the maximum in-plane shear stress in ksi? %3D

Q: Problems 9-5: Determine the normal stress and shear stress acting on the inclined plane AB. Solve…

Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…

Q: PROBLEM 1.25 For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in…

A: 1.25 Consider the free-body diagram as shown below for the point B.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

If ox = 20 ksi, oy = -30 ksi and Txy = 0 ksi, determine the von Mises stress.
a.
61.2
43.6
b. 52.9
33.8
C.
d.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A material has a yield strength of 500 MPa. At a stress of X MPa, the strain is measured as Y. What is the elastic modulus in GPa? X = 470 Y = 0.0033 a. 102.42 O b. 122.42 O c. 142.42 d. 162.42 e. 182.42
11
! Required information Consider the given state of stress. Given: X = 5 ksi and Y = 25 ksi. + 6 ksi X Determine the normal stress using Mohr's circle. The normal stress is 3.34 ksi.
Determine the maximum principal stress (in ksi) for the state of stress at a point shown below. a. b. 37.1 47.1 40 ksi 30 ksi 80 ksi C. 57.1 d. Answer is not among the choices
A load P is supported by two (2) concentric steel springs. The inner spring consists of 40 turns of 20 mm diameter wire on a mean diameter of 150 mm, the outer spring has 30 turns of 30 mm diameter wire on a mean diameter of 200 mm. Use G= 83000 MPa. a) Determine the maximum load that the inner spring could carry so as not to exceed a shearing stress of 140 MPa. b) Determine the maximum load that the outer spring could carry so as not to exceed a shearing stress of 140 MPa. c) Determine the maximum load that the spring could carry.
Part 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=12 ft, b=6 ft and w = 10 kips/ft. "| Ay Answers: Ay= Mo W i a Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) "|| B PO W b B b kips, Cy= i C X C₂ X kips.
1. If o, = 20 ksi, o, = 10 ksi, and txy = 30 ksi, what is the absolute maximum shear stress for the given stress %3D state? → 6x Tay a. 30.4 с. 38.2 b. 35.1 d. Answer is not among the choices
) The curve of stress versus time on the cross section of engine connecting rod is shown in the =-10.75N/ mm? . 1) following Fig. oax = 78.61N /mm,omin Calculate: Mean stress om; Alternating stress oa; Stress ratio y. t 78. 61 -10.75
The state of stress at a point in a member is shown on the element. Suppose that σx= 25 MPa, σy= 100 MPa, and τxy= 53 MPa. A) Determine the normal stress acting on the plane AB. B) Determine the shear stress acting on the plane AB.
17. The frame shown carries a load P = 2000 lb. If a = b = 10 inches, c = 18 inches, and s= 3/8 inch. Determine the stress in strut BD in ksi. a. 30.5 b. 34.2 a b PA D B C. d. 39.0 46.1 C 22 24 section A-A: Is 18. The motion of the follower of a cam-follower system is governed by x = R(1 + 1/2 cosoot). If R = 70 mm and co = 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 C. b. 20 d.
23. Determine the stress, in MPa, in member DF if its cross sectional area is 900 mm². a. 165 b. 178 4 m a. b. B C 100 KN 6 m 3 m 200 kN 4 m E 3m F O ΟΠΟΙΟΙ C. d. 24. Determine the largest load (in kN) that a 8 mm pin can support if it is in single shear and the working stress is 160 MPa. 16.1 32.2 214 250 C. d. 48.0 Answer is not among the choices
Required information Consider the given state of stress. Given: A = 4 ksi and B= 20 ksi. + + B + 6 ksi Determine the orientation of the planes of maximum in-plane shearing stress. The orientations of the planes of maximum in-plane shearing stress are - 31.3 and 108.4.