Part 3 * Incorrect. Use the normal stress transformation equation, Equation on = 0x cos²0 + oysin²0 + 2Txy sin cos on = σxcos² 0 + 0,sin²0 + 2txy sin cose. The angle 00 shown in the figure above is equal in magnitude to the angle ßß given in the problem statement. Note that 00 turns clockwise from the xx axis, so when used in Equation σ₁ = σcos²0 + σ,sin²0 + 2+xy sin cos0σ„ = σ¸cos²0 + ¤,sin²0 + 2xy sin cos0,00 is negative. Determine the normal stress perpendicular to the weld seams. This is the normal stress in the n direction shown in the figure below. Use the correct sign based on the sign convention for normal stress. P On = i -106.536 eTextbook and Media Hint B Save for Later 10 n MPa Use the normal stress transformation equation, Equation o, = ₂cos²0 + o₂sin²0 + 2Txy sin cose. Assistance Used Assistance Used Attempts: 5 of 6 used Submit Answer

Part 3 * Incorrect. Use the normal stress transformation equation, Equation on = 0x cos²0 + oysin²0 + 2Txy sin cos on = σxcos² 0 + 0,sin²0 + 2txy sin cose. The angle 00 shown in the figure above is equal in magnitude to the angle ßß given in the problem statement. Note that 00 turns clockwise from the xx axis, so when used in Equation σ₁ = σcos²0 + σ,sin²0 + 2+xy sin cos0σ„ = σ¸cos²0 + ¤,sin²0 + 2xy sin cos0,00 is negative. Determine the normal stress perpendicular to the weld seams. This is the normal stress in the n direction shown in the figure below. Use the correct sign based on the sign convention for normal stress. P On = i -106.536 eTextbook and Media Hint B Save for Later 10 n MPa Use the normal stress transformation equation, Equation o, = ₂cos²0 + o₂sin²0 + 2Txy sin cose. Assistance Used Assistance Used Attempts: 5 of 6 used Submit Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asiacell lI. A docs.google.com اسم الطالب الثلاثي* إجابتك The second moment of area for the following figure is 3omm إجابتك صفحة 1 من 1 : إرسال
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate the units of each measurement. Calculate the average length of each side of the block. Dimension Caliper (Units) 0.995 1.455 0.985 Ruler(in) A: 0.9 B: 1.5 C: 0.9 A B C Dimension A B Instrument Use the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record the voltage on the table below: LVDT Offset: 0.556 (Do not include the offset value in your average dimensions) C Ave Dimension (Units) (Dial Gauge) 0.997 1.659 0.949 0.964 in 1.538 in 0.945 in oltage Average Dimension 1.244 volt 1.994 1.28 0.964 in 1.538 in 0.945 in
B 45 20 R20 20 IS 70 90
what is f and g ? what is g and f ? l = .5 finger width x = Arm length g = eye level height d = object distace A = angle from eye level to top of the object f = object height from eye level h = diameter of the sun .0127 m .7112 m 1.49668x 10^11 m 1.023 degrees 2.673 x 10^9 m
use moher
B9
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 44 B = 78 40 20 10 Ø10 40 20 B 15 10 15 R20 30 10 T 20-
Find the front, side, and top projection
A piston ring from the piston in the previous problem needs to be replaced.Its thickness is measured using a vernier caliper. The vernier is shown. Whatis the thickness of the replacement ring?
p A667849305_17711 26_2021_Ass X O File | C:/Users/acer/Downloads/A667849305_17711_26_2021_Assignment%202%20MEC107.pdf of 3 (D Page view A Read aloud V Draw E Highlight O Erase Q. 1 Determine the moment of Inertia about given x and y axis in the following figure if a = 10 mm. -2a X Activate Windows Go to Settings to activate Windows. 12:46 O Type here to search 4») G ENG 03-04-2021 近