Determine the maximum shearing stress is T=40 kN-m.TABLE 3.1. Coefficients for200 mmRectangular Bars in Torsiona/b|40 mm1.00.2080.14061.21.52.00.2190.16610.2310.2460.19580.229100 mm2.50.2580.2493.00.2670.2634.00.2820.2815.010.00.2910.29120 mm0.3120.3120.3330.333

Answered: Image /qna-images/answer/2a350eb5-9e1d-4519-bdef-d38e1807a611.jpg

Determine the maximum shearing stress is T=40 kN-m. TABLE 3.1. Coefficients for Rectangular Bars in Torsion 200 mm a/b | 40 mm 1.0 0.208 0.1406 0.1661 0.1958 0.229 0.249 0.263 0.281 0.291 0.312 1.2 0.219 1.5 0.231 2.0 0.246 100 mm 2.5 3.0 0.258 0.267 0.282 4.0 5.0 0.291 20 mm 10.0 0.312 0.333 0.333

Determine the maximum shearing stress is T=40 kN-m. TABLE 3.1. Coefficients for Rectangular Bars in Torsion 200 mm a/b | 40 mm 1.0 0.208 0.1406 0.1661 0.1958 0.229 0.249 0.263 0.281 0.291 0.312 1.2 0.219 1.5 0.231 2.0 0.246 100 mm 2.5 3.0 0.258 0.267 0.282 4.0 5.0 0.291 20 mm 10.0 0.312 0.333 0.333

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.7 mm and upward by v = 3.5 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 720 mm, a = 31% and 3 = 59° Answer: y = i P R urad
Please solve correctly
Given the figure with its V = 45 kN; bf = 95 mm; bw = 20 mm; d = 115 mm; tf = 28. What is the horizontal shearing stress? %3D %3D br2 Neutral Axis d br2
The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress s limited to 5000 psi. Assume single shear. 4R + 3t
Situation 1| Consider the figure 1 below. 3 - 25mmø bolts are used to fasten a plate to a steel beam. 1) Determine the average shearing stress caused in each bolt by the 30kN loads 2) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 60MPA. 30 kN 150. 300 200. 30 kN P. 75 P.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.6 mm and upward by v = 5.2 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 620 mm, a = 29°, and B = 61°. 41 Answer: y = i urad
A load P is supported by two (2) concentric steel springs. The inner spring consists of 40 turns of 20 mm diameter wire on a mean diameter of 150 mm, the outer spring has 30 turns of 30 mm diameter wire on a mean diameter of 200 mm. Use G= 83000 MPa. a) Determine the maximum load that the inner spring could carry so as not to exceed a shearing stress of 140 MPa. b) Determine the maximum load that the outer spring could carry so as not to exceed a shearing stress of 140 MPa. c) Determine the maximum load that the spring could carry.
Part 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=12 ft, b=6 ft and w = 10 kips/ft. "| Ay Answers: Ay= Mo W i a Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) "|| B PO W b B b kips, Cy= i C X C₂ X kips.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.0 mm and upward by v = 4.2 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 775 mm, a = 20%, and B = 70% ↑= Answer: y = i P a B R urad
a. Compute the maximum shearing stress at point B in MPa. b. Compute the normal stress at point B in MPa. c. Compute the maximum compressive stress at point B in MPa. d. Compute the shearing stress at point A in MPa e. Compute the normal stress at point A in MPa.
Do problem 1.26 question a
Write answer