I Design a CS amplifier using E-MOSFET with voltage gain 6, VGs=6V ( gm=4500µS ).Il-(a) State the fundamental operating principle of the field-effect transistor as a switch.(b) Design a MOSFET NOR circuitVppIII Find the Q point of the given JFET circuit.+6 VIpss = 5 mA. Vp=4VRp820 NRsRG10 M2330 NIV-. From the circuit of common source JFET amplifier shown in the figure,its has Vas(om = -2.0V,VpoInss = 1.4mA. If you need this amplifier to be biasedwith ID =0.7mA, VDD = 20V, and voltage gain of 20dB,C3what is the value of RS, and RD?oVoutGVinRGAssignment/Home Work

Since you have asked multiple question ,we will slove the first question for you .If you want any…

Answered: I Design a CS amplifier using E-MOSFET…

Engineering

Electrical Engineering

I Design a CS amplifier using E-MOSFET with voltage gain 6 , Vas-6V (gm=4500µS).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1:- For the emitter bias circuit shown in figure(1), if Vec-20V, B-50, RC-2k2, RB-430k2, and RE=1kQ. Vee (a) Determine IB, IC, and IE. (b) Determine VCE, VC, VE, VB. RB (c) Draw the de load line. Vo (d) The stability factor SICO. vì For the amplifier
b) In your own understanding in the field of electronics analyze the advantages of BJT over MOSFET
A common emitter amplifier has a 15V power supply. If we design for a 6.5V swing (peak voltage) at the output voltage what will the DC voltage drop be across RE? Group of answer choices 2V 10V 6.5 5V
For a common-collector amplifier, RE = 100N, r. = 10N, and 30ac = 150. If a 10 mV signal is applied to the base , the output signal is approximately 10 mV 150 mV 1.5 V 100 mV
Explain the math
Question 1: For the Mosfet in the circuit shown below: VTp = - 0.8V, and Kp = 200 uA/V2. Find Vs and Vp. Where Kp = ½ kp'W/L. lo=0.4 m Vs R= 50 k2 Rp=S ka -5 V
10-when the emitter resistance RE doubles the ac emitter resistance a-Increases. b-decreases. c-Remains the same. d-Cannot be determined. 11-To reduce the distortion in a CE amplifier, reduce the a-DC emitter current. b-Base-emitter voltage. c-Collector current. d-AC base voltage. 12-The output voltage of a CE amplifier is a-Amplified. b-Inverted. c-180° out of phase with the input. d-All of the above.
Use 2 decimal places A CS JFET amplifier has gm= 6.82 mS, with a drain resistance of 1.13 kohms and load resistance of 685.52 ohms. Voltage gain (absolute value) is Round your answer to 2 decimal places.
Figure 1 shows the transfer curves of two different type of FET transistors. The transfer curve of transistor A is shown in Figure 1(a) that has ID(on) = 5mA and VGS(on) = 7V. Meanwhile, the transfer curve of transistor B is shown in Figure 1(b). (i) Determine the type of transistor A and B. (ii) State the correct equation for the transfer curve A and B. (iii) Sketch the basic construction of transistor A and B and label each part correctly. (iv) Briefly discuss one similarity in terms of the construction between the transistors A and B. 4'o (mA) D (mA) 8 12 11 7 10 5 4 6. 3 2 1 2 3 4 5 6. 7 8 VGS 1 -5 -4 -3 -2 -1 VGs Figure 1(a) Figure 1(b)
Vi RB Vcc Rc our A BJT (B=200) is implemented in an amplifier circuit, with a VCC of 15 volts. One wishes to set the Q point at IC = 5.76 mA and VCE = 6.73 volts (DC). Determine RB.
Q.6 Determine the values of transconductance for an n-channel enhancement MOSFET having threshold voltage VT = 3V at the following operating points (i) 6V and (ii) 8V
I Design a CS amplifier using E-MOSFET with voltage gain 6 , Ves=6V (gm-4500uS ). Il-(a) State the fundamental operating principle of the field-effect transistor as a switch. (b) Design a MOSFET NOR circuit III Find the Q point of the given JFET circuit. VDD +6 V Ipss 5 mA. Vp-4V 820 0 RG 10 MQ Rs 330 N IV From the circuit of common source JFET amplifier shown in the figure, its has VGS(of = -2.0V, Ipss = 1.4mA. If you need this amplifier to be biased with Ip =0.7mA, VDp= 20V, and voltage gain of 20DB, what is the value of RS, and RD? C3 Vout Assignment Home Work